Rock Mechanics
sadegh Amoun; Hamid Chakeri
Abstract
This study is an attempt to design and manufacture a tunnel boring machine (TBM) simulator to better understand the interaction between soil and cutting tools, due to the lack of an accepted method for this issue. In this paper, Sahand Soil Abrasion Test (SSAT) is introduced, which is built by the Sahand ...
Read More
This study is an attempt to design and manufacture a tunnel boring machine (TBM) simulator to better understand the interaction between soil and cutting tools, due to the lack of an accepted method for this issue. In this paper, Sahand Soil Abrasion Test (SSAT) is introduced, which is built by the Sahand University of Technology. The experimental and real results of tool wear are presented. The results firstly demonstrate that the cutting tools wear in the coarse-grained soils can be less than in the fine-grained ones in the real conditions. However, in the soils with fine grains higher than 10%, the wear of cuttings tools increase in the laboratory condition when grading parameters increase. In soils with fine grains less than 10%, the wear of tools decreases by increasing the grading parameters. Also the results reveal that the coefficient of gradation depend on the amount of silt and clay in the soil samples. The investigations show that sorting is another good criterion for investigating the power of soil abrasively. Furthermore, it indicates that the cutting tools wear increases when the moisture content of the soil structure in the dense condition approaches the optimal moisture content. Finally, the results indicate that the wear and torque of the cutterhead could be reduced by 58% and 34%, respectively, when the excavated materials have the appropriate conditioning.
Rock Mechanics
Hamid Chakeri; Faezeh Barri; Mohammad Darbor; Hamed Haghkish
Abstract
Excavation with Tunnel Boring Machine (TBM) in urban environments can have risks, such as ground surface settlement. The empty space between the cutterhead and the segment should be filled with suitable grout during the excavation. Nowadays, using grout behind the segment and other fillers fill the empty ...
Read More
Excavation with Tunnel Boring Machine (TBM) in urban environments can have risks, such as ground surface settlement. The empty space between the cutterhead and the segment should be filled with suitable grout during the excavation. Nowadays, using grout behind the segment and other fillers fill the empty space behind the segment and reduce the amount of ground surface settlement. Undoubtedly, using a grout with appropriate mechanical behavior can be a suitable substitute for excavated soil in mechanized tunneling. In this research, the mechanical behavior of the grout behind the segment during injection into the space between the soil and the segment and its mixture with the soil is studied. Also, the effect of mechanical properties of grout mixed with soil on the ground surface settlement is investigated using numerical modeling. The components of two-component grout of this study comprises Sufian type 2 cement with 28-day strength of 44 MPa and density of 3050 kg/m3, Salafchegan bentonite with density of 2132 kg/m3 and precipitator of liquid sodium silicate with density of the solution 1500 kg/m3. The results of the laboratory studies indicated that mixing the grout and soil increases the mechanical properties of grout significantly. Increasing the soil in the mixture of soil and grout up to 40% increases the uniaxial compressive strength up to 300%, the elasticity of modulus up to 156% and the cohesion of the mixture up to 100%. On the other hand, based on the results of numerical modeling, the proper injection pressure can significantly reduce the ground surface settlement. Increasing the injection pressure from 0 to 120 kPa has a 17% influence on the reduction of ground surface settlement.
Rock Mechanics
Taha Ansari; Hamid Chakeri; Mohammad Darbor; sadegh Amoun; Hadi Shakeri
Abstract
There is no acceptable method for investigating the tool wear phenomenon in soft grounds. In this article, first, a new equipment made at Sahand University of Technology is introduced, which is used for simulation of TBM tunneling mechanism. Next, the effect of various soil grading parameters such as ...
Read More
There is no acceptable method for investigating the tool wear phenomenon in soft grounds. In this article, first, a new equipment made at Sahand University of Technology is introduced, which is used for simulation of TBM tunneling mechanism. Next, the effect of various soil grading parameters such as D10, D30, and D60 (which indicate the corresponding diameters on the soil grading diagram where 10, 30, and 60% of the grains are smaller than these values, respectively), coefficient of gradation, uniformity coefficient, sorting coefficient and effective size on the cutting tools wear. The initial studies show that in soils with fine grains greater than 10%, by increase in the values of D10, D30, D60, and effective size, the tool wear increases. However, in soils with fine grains less than 10%, by increase in the above-mentioned parameters, the soil abrasiveness reduces. Also in soils with more than 10% fine grains, by increase in the coefficient of gradation value, the soil abrasiveness reduces. But in soils with fine grains less than 10%, by increase in the value of this parameter, the tool wear increases. The results of experiments show that sorting coefficient could be a good criterion for investigating the soil abrasiveness.
S. Akbari; Sh. Zare; H. Chakeri; H. Mirzaei Nasir Abad
Abstract
Evaluation of the interaction between a new and the existing underground structures is one of the important problems in urban tunneling. In this work, using FLAC3D, four numerical models of single- and twin-tube tunnels in urban areas are developed, where the horizontal distance between the single- and ...
Read More
Evaluation of the interaction between a new and the existing underground structures is one of the important problems in urban tunneling. In this work, using FLAC3D, four numerical models of single- and twin-tube tunnels in urban areas are developed, where the horizontal distance between the single- and twin-tube tunnels are varied. The aim is to analyze the effects of the horizontal distances, considering various criteria such as the deformation of linings, the forces and moments exerted on the twin-tube tunnels and their safety factors, the subsidence that occur on the surface and the nearby buildings, the stability of the single-tube tunnel, and the stability of the pillar lying between the single- and twin-tube tunnels. Considering the above-mentioned criteria, the results obtained indicate that the interaction between the single- and twin-tube tunnels is virtually negligible in the distance more than three times the single-tube tunnel diameter. Also the stability of the pillar lying between the tunnels makes the distance to be chosen at least 1.5 times the single-tube tunnel diameter.
