Alireza Dolatshahi; Ali Nouri Qarahasanlou
Abstract
Engineers use various methods to evaluate the performance of concrete structures under dynamic loads, including numerical simulations, laboratory experiments, and field tests. By combining the results of these methods, the engineers can develop a comprehensive understanding of the behavior of concrete ...
Read More
Engineers use various methods to evaluate the performance of concrete structures under dynamic loads, including numerical simulations, laboratory experiments, and field tests. By combining the results of these methods, the engineers can develop a comprehensive understanding of the behavior of concrete structures under dynamic loads and use this information to design more resilient structures capable of withstanding these loads. In this work, four models of the concrete lining of the circular tunnel are simulated to investigate the effect of the pre-cracked in the tunnel's concrete lining under an internal explosion loading. A crack in three different locations at angles of 0, 45, and 90 on the horizontal axis of the tunnel is investigated and analyzed. The coupled Eulerian-Lagrangian method and the constitutive behavior, such as concrete damage plasticity for concrete and Drucker-Prager for soil, allows a more accurate simulation of the internal explosion loading scenario. The selection of Trinitrotoluene and the Jones-Wilkins-Lee equation of state for the explosive provides a realistic representation of the behavior of the explosive material. The modeling results show that in an internal explosion, by examining three different locations of a crack in the concrete, the occurrence of a crack in the crown of the tunnel is more critical than two crack locations. Hence, the existence of a crack with a length of 100 cm and a depth of 15 cm in the crown of the tunnel increases the tensile damage zone by 16.59% compared to the case where there is no crack.
Mehdi Hosseini; Alireza Dolatshahi; Esmaeel Ramezani
Abstract
This work investigates the effect of adding micro-silica as a pozzolan and a replacement for part of concrete cement when placing concrete in an acidic environment. Two types of ordinary concrete and concrete-containing micro-silica are constructed. The specimens are subjected to 0, 1, 5, and 10 cycles ...
Read More
This work investigates the effect of adding micro-silica as a pozzolan and a replacement for part of concrete cement when placing concrete in an acidic environment. Two types of ordinary concrete and concrete-containing micro-silica are constructed. The specimens are subjected to 0, 1, 5, and 10 cycles for two hours inside two types of acidic water containing sulfuric and nitric acid with pH = 3 and normal water with pH = 7. Mechanical properties including Brazilian tensile strength and uniaxial compressive strength, and physical properties including effective porosity, water absorption, and the longitudinal wave velocity of specimens are determined after the mentioned number of cycles. Thr results show that by decreasing the pH and increasing the number of cycles, the effective porosity and water absorption increase, and the velocity of longitudinal waves, Brazilian tensile strength, and uniaxial compressive strength of concrete decrease. Replacing 10% of micro-silica as a part of concrete cement has boosted the durability of concrete in corrosive conditions containing sulfuric and nitric acid more than ordinary concrete.
M. Hosseini; A.R. Dolatshahi; E. Ramezani
Abstract
Concrete is among the widely used materials in all industries and mineral and civil activities worldwide, highlighting its significance. Most natural and non-natural phenomena can influence the concrete's physical and mechanical properties, causing many irreparable damages. Acid rain is a natural inevitable ...
Read More
Concrete is among the widely used materials in all industries and mineral and civil activities worldwide, highlighting its significance. Most natural and non-natural phenomena can influence the concrete's physical and mechanical properties, causing many irreparable damages. Acid rain is a natural inevitable phenomenon, particularly in industrial zones with high pollution percentages.This work investigates the effect of acid rain on the concrete specimens containing micro-silica and limestone powder. To this end, the concrete specimens are divided into six groups. Throughout this paper, CN represents the concrete without micro-silica and limestone powder under no-rain conditions, CO is the concrete without micro-silica and limestone powder under normal rain conditions, CA is the concrete without micro-silica and limestone powder under acid rain conditions, CMLN is the concrete containing micro-silica and limestone powder under no-rain conditions, CMLO is the concrete containing micro-silica and limestone powder under normal rain conditions, and CMLA shows the concrete containing micro-silica and limestone powder under acid rain conditions. The measured physical properties are the effective porosity, dry density, water absorption, and velocity of longitudinal waves. The mechanical properties including the Brazilian tensile strength, uniaxial compressive strength, triaxial compressive strength, cohesion, and internal friction angle are also measured. For the samples of CN and CMLN, they are tested under no rainfall conditions, whereas the samples of CA and CMLA are tested after 20 cycles of acid rain (pH = 2). The samples of CO and CMLO are also tested after undergoing 20 normal rain cycles (urban water with pH = 7). In each test cycle, there is 1 hour of rain and 1 hour of no rain. The results obtained show that adding micro-silica and limestone powder improves its properties so that the decrease in the effective porosity, longitudinal wave velocity, dry unit weight, water absorption, Brazilian tensile strength, uniaxial compressive strength, cohesion, and internal friction angle of the specimens of CMLA is less than those for the specimens of CA.
M. Hosseini; D. Fakhri
Abstract
The purpose of this work is to investigate the possibility of using mine wastes in the improvement of concrete properties. This research work investigates the physical and mechanical properties of the concrete specimens. These concrete specimens include concrete-lacking fibres, micro-silica and limestone ...
Read More
The purpose of this work is to investigate the possibility of using mine wastes in the improvement of concrete properties. This research work investigates the physical and mechanical properties of the concrete specimens. These concrete specimens include concrete-lacking fibres, micro-silica and limestone powder (C), concrete-containing glass fibres without micro-silica and limestone powder (GC), concrete-containing micro-silica and limestone powder without fibres (CML), and concrete-containing glass fibres, micro-silica, and limestone powder (CGML). The physical and mechanical properties including the effective porosity, longitudinal wave velocity, water absorption, unit weight, tensile strength, uniaxial compressive strength, triaxial compressive strength, cohesion, and internal friction angle are investigated. The results obtained show that adding glass fibres to the concrete (GC) improve its properties compared to the fibre-less concrete (C). However, the properties of GC are improved significantly less than CGML. The Brazilian tensile strength and uniaxial compressive strength of GC increase by 13.6% and 10.95% relative to C. The Brazilian tensile strength and uniaxial compressive strength of CGML increase by 21.8% and 45.94% relative to C. Finally, it can be concluded that adding the micro-silica and limestone powder to the glass fibre concrete as well as the use of mine wastes also significantly improves the properties of the concrete.