Mine Economic and Management
Rahman Ahmadi; Rahim Dabiri; Bijan Taheri
Abstract
This study applies risk analysis and the Analytic Hierarchy Process (AHP) to evaluate sustainable mining development in four protected, restricted, and military areas of Qazvin Province. A sequential hybrid framework is used in which GIS–Fuzzy modelling provides mineral-prospectivity screening, ...
Read More
This study applies risk analysis and the Analytic Hierarchy Process (AHP) to evaluate sustainable mining development in four protected, restricted, and military areas of Qazvin Province. A sequential hybrid framework is used in which GIS–Fuzzy modelling provides mineral-prospectivity screening, AHP quantifies the relative importance of the retained decision criteria, and a semi-quantitative probability–impact matrix provides area-specific risk comparison. Mining conditions in Alamut, Bashgol, Tarom, and Artesh Lands were evaluated using expert judgments and Expert Choice, with the final comparison expressed as normalized incentive and limiting contributions. In the preliminary six-parameter influence assessment, environmental considerations had the highest influence (0.327), approximately 1.7 times the economic and legal/policy parameters (0.188 each) and approximately 3.3 times the three lower-weight parameters (0.099 each). In the reduced AHP model, Environmental, Security & Conflict also received the highest criterion weight (0.581). Artesh Lands showed the most favorable risk balance, Bashgol ranked second under conditional environmental controls, and Alamut and Tarom remained jointly least favorable because their retained criterion inputs were identical. The framework is intended as a strategic decision-support tool and does not replace environmental impact assessment or regulatory authorization.
Mineral Processing
R. Ahmadi; E. Ravanasa; Y. Mirzapour
Abstract
In this work, adsorption of the potassium amyl xanthate collector on the pure chalcopyrite surface was studied by applying atomic force microscopy (AFM). The adsorption experiments were carried out at different concentrations of the collector and at diverse pH values in the presence or absence of exterior ...
Read More
In this work, adsorption of the potassium amyl xanthate collector on the pure chalcopyrite surface was studied by applying atomic force microscopy (AFM). The adsorption experiments were carried out at different concentrations of the collector and at diverse pH values in the presence or absence of exterior ions. The changes occurring in the surface morphology of chalcopyrite due to the collector adsorption were evaluated by measuring the contact angle of the collector and its surface coating. According to the 3D images obtained by AFM, an increase in the pH value from 7.5 to 9.5 at two concentrations of 25*10-3 and 50*10-3 g/ton of the collector would increase the number of particles adsorbed on the surface, improve the adsorption morphology, and reduce the contact angle. Moreover, at a constant pH value, increasing the collector would result in the proliferation of contact angles as well as a relative increase in the number of particles. By comparing the morphological surface changes in the tap and distilled water samples, applying tap water, owing to the presence of Cu2+ ions and activation of the surface through the production of CuS, the quality and quantity of adsorption would be increased. The use of tap water not only can account for an appropriate coating by the collector but also causes to reduce the consumption of collector for at least 50%.
Mineral Processing
S. Nazari; Seyed Ziaedin Shafaei; M. Gharabaghi; R. Ahmadi; B. Shahbazi
Abstract
In this work, the effects of the types of frother (MIBC, pine oil, and A65) and operational parameters (impeller speed and air flow rate) on the flotation of quartz coarse particles was investigated using nano bubbles (NBs). Quartz particles of the size of -425+106 mm and three types of frother were ...
Read More
In this work, the effects of the types of frother (MIBC, pine oil, and A65) and operational parameters (impeller speed and air flow rate) on the flotation of quartz coarse particles was investigated using nano bubbles (NBs). Quartz particles of the size of -425+106 mm and three types of frother were used for the flotation experiments. Also the impeller speed was 600 to 1300 rpm, and the air flow rates were 30 and 60 L/h. In the absence of NBs, the maximum recovery was achieved with the pine oil frother, an impeller speed of 1000 rpm, and an air flow rate of 60 L/h. In the presence of NBs, the maximum recovery was achieved using pine oil at an impeller speed of 900 rpm and an air flow rate of 30 L/h. However, increasing the recovery in the presence of NBs, compared to the absence of NBs for MIBC, was more than the other two frothers, and the recovery using this frother to increase up to 25% but using pine oil, the recovery increased up to 23%. The lowest recovery in the presence of NBs was obtained using A65. Also the use of NBs increased recovery in all the three fractions compared to the absence of NBs but the presence of NBs increased the recovery of particles with size of -212+106 mm more than the particle size in the ranges of -300+212 and -425+300 mm.