Rock Mechanics
Navid Afrasiabi; Mehdi Noroozi; Ahmad Ramezanzadeh
Abstract
In this research, the effect of geometric parameters of closely joints on rock cutting efficiency by TBM disc cutter is studied using PFC3D software. A validated numerical model of linear cutting machine test is developed and the efficiency of disc cutter is investigated on rock mass specimens with different ...
Read More
In this research, the effect of geometric parameters of closely joints on rock cutting efficiency by TBM disc cutter is studied using PFC3D software. A validated numerical model of linear cutting machine test is developed and the efficiency of disc cutter is investigated on rock mass specimens with different joint configurations (possible combination of dip angles of 30, 60, 90 degrees with joint spacings of 3, 5, 10, 15, 20 cm). Numerical modeling results reveal that in general, the joint spacing has a greater effect on rock cutting efficiency than joint orientation. If the joint spacing is less than 10 cm, the role of the joint angle is reduced and the distances between the joints control the efficiency. When the joints are close together and have a spacing of less than 10 cm, particularly 3 to 5 cm, the best cutting efficiency can be achieved for a joint angle of 90 degrees. The cutting coefficient is decreased by increasing the joint spacing and the maximum CC occurs at a joint spacing of 5 cm. For joint spacing more than 10 cm, the joints with a 90 degrees dip angle have the greatest impact on the specific energy and reduce cutting efficiency. The best disc cutter efficiency and the minimum required normal force is achieved when joint spacing is more than 10 cm and the angle between the joints and advance direction of the disc cutter is 60 degrees. In the tunnel excavation process, with increasing joint spacing, the TBM machine thrust is more important than its torque. The findings of this research provide a basis for predicting TBM efficiency through joint characteristics.
Rock Mechanics
M. Noroozi; R. Rafiee; M. Najafi
Abstract
Various structural discontinuities, which form a discrete fracture network, play a significant role in the failure conditions and stability of the rock masses around underground excavations. Several continuum numerical methods have been used to study the stability of underground excavations in jointed ...
Read More
Various structural discontinuities, which form a discrete fracture network, play a significant role in the failure conditions and stability of the rock masses around underground excavations. Several continuum numerical methods have been used to study the stability of underground excavations in jointed rock masses but only few of them can take into account the influence of the pre-existing natural fractures. In this work, the pre-existing fractures are explicitly modeled as a Discrete Fracture Network (DFN) model, which is fully coupled with the FEM modeling for stability analysis of support systems in a diversion tunnel at the Rudbar Lorestan dam site. Hence, at first, using the surveyed data in the diversion tunnel and an estimation of the suitable probability distribution function on geometric characteristics of the existing joint sets in this region, the 3D DFN model was simulated using the stochastic discrete fracture networks generator program, DFN-FRAC3D. In the second step, a coupled 2D Finite Element Method and the prepared stochastic model were used for analysis of existent (based on technical reports) recommended support systems. The objective here is to grasp the role of the fracture networks on the results of the tunnel stability analysis using FEM modeling and also to compare the results with those obtained through stability analysis without considering the effect of fractures.
M. Noroozi; R. Kakaie; Seyed M. E Jalali
Abstract
Fault zones and fault-related fracture systems control the mechanical behaviors and fluid-flow properties of the Earth’s crust. Furthermore, nowadays, modeling is being increasingly used in order to understand the behavior of rock masses, and to determine their characteristics. In this work, fault ...
Read More
Fault zones and fault-related fracture systems control the mechanical behaviors and fluid-flow properties of the Earth’s crust. Furthermore, nowadays, modeling is being increasingly used in order to understand the behavior of rock masses, and to determine their characteristics. In this work, fault zones and fracture patterns are reviewed, and also comprehensive studies are carried out on the fracture geometry and density variations. A model to describe damage zones around the strike-slip faults is developed, in which the range of damage zone styles commonly found around strike-slip fault zones are shown. A computer code, named DFN-FRAC3D, is developed for the two- and three-dimensional stochastic modeling of rock fracture systems in fault zones. In this code, the pre-existing and fault-related fractures are modeled by their respective probability distributions, and the joint density may be varied by the distance from the fault core. This work describes the theoretical basis and the implementation of the code, and provides a case study in the rock fracture modeling to demonstrate the application of the prepared code.
