Vahab Sarfarazi; Hadi Haeri; Fereshteh Bagheri; Erfan Zarrin ghalam; Mohammad Fatehi Marji
Abstract
The tensile strengths of geomaterials such as rocks, ceramics, concretes, gypsum, and mortars are obtained based on the direct and indirect tensile strength tests. In this research work, the Brazilian tensile strength tests are used to study the effects of length and inclination angle of T-shaped non-persistent ...
Read More
The tensile strengths of geomaterials such as rocks, ceramics, concretes, gypsum, and mortars are obtained based on the direct and indirect tensile strength tests. In this research work, the Brazilian tensile strength tests are used to study the effects of length and inclination angle of T-shaped non-persistent joints on the mechanical and tensile behaviors of the geomaterial specimens prepared from concrete. These specimens have a thickness of 40 mm and a diameter of 100 mm, and are prepared in the laboratory. Two T-shaped non-persistent joints are made within each Brazilian disc specimen. The Brazilian disc specimens with T-shaped non-persistent joints are tested experimentally in the laboratory under axial compression. Then these tests are simulated in the two-dimensional particle flow code (PFC2D) considering various notch lengths of 6, 4, 3, 2, and 1 cm. However, different notch inclination angles of 0, 30, 60, 90, 120, and 150 degrees are also considered. In this research work, 12 specimens with different configurations are provided for the experimental tests, and 18 PFC2D models are made for the numerical studies of these tests. The loading rate is 0.016 mm/s. The results obtained from these experiments and their simulated models are compared, and it is concluded that the mechanical behavior and failure process of these geomaterial specimens are mainly governed by the inclination angles and lengths of the T-shape non-persistent joints presented in the samples. The fracture mechanism and failure behavior of the specimens are governed by the discontinuities, and the number of induced cracks when the joint inclination angles and joint lengths are increased. For larger joints when the inclination angle of the T-shaped non-persistent joint is around 60 degrees, the tensile strength is minimum but as it is closed to 90 degrees, the compressive strengths are maximum. However, an increase in the notch length increase the overall tensile strength of the specimens. The strength of samples decreases by increasing the joint length. The strain at the failure point decreases by increasing the joint length. It is also observed that the strength and failure process of the two sets of specimens and the corresponding numerical simulations are consistence.
V. Sarfarazi; K. Asgari; Sh. Mohamadi Bolban Abad
Abstract
The interaction between an internal hole and two surrounded joints under a uniaxial compression are examined using the experimental and discrete element procedures. Inside the concrete sample, two notches and an internal hole are created. The joint angle change from 0° to 90° with an increment ...
Read More
The interaction between an internal hole and two surrounded joints under a uniaxial compression are examined using the experimental and discrete element procedures. Inside the concrete sample, two notches and an internal hole are created. The joint angle change from 0° to 90° with an increment of 30°. The distances between the joint and the internal hole are 2 cm and 3 cm. Also the numerical models are provided. The joint angle change from 0° to 90° with an increment of 15°. The distances between the joint and the internal hole are 2 cm, 3 cm, and 4 cm. The compressive strength is 7.2 MPa. The rate of loading is 0.005 mm/s. The experiment indicates that the failure process is significantly dependent on the notch angle and the joint distance from the hole. The pattern of fracture and mechanism of failure of joints affect the shear strengths of the samples. The models with joint angles of 30° and 60° have a less compressive strength since the pure tensile failure occurs in these configurations. The model strength decreases with decrease in the join spacing. In fact, in the case that the joint spacing is 2 cm, the interaction between the hole and the neighboring joint is so strong. Consequently, the compressive strength is declined. In both approaches of the numerical simulation and experimental methods, the pattern and strength of failure are identical.
