Mineral Processing
Mohammad Javad Kazemzadeh Zazerani; Mohammad Reza Khalesi
Abstract
The Carbon-in-Leach (CIL) process involves complex mass transfer among solid, liquid, and carbon phases, making predictive modeling and soft-sensor development inherently challenging. Reliable time-resolved data remain one of the main obstacles to digital transformation in mineral processing, as measurement ...
Read More
The Carbon-in-Leach (CIL) process involves complex mass transfer among solid, liquid, and carbon phases, making predictive modeling and soft-sensor development inherently challenging. Reliable time-resolved data remain one of the main obstacles to digital transformation in mineral processing, as measurement noise and phase inconsistencies hinder reproducibility, mass balance closure, and model calibration. Despite extensive kinetic and simulation studies on CIL circuits, validated dynamic data reconciliation frameworks that explicitly account for carbon transfer and transient multiphase behavior remain limited, leaving an important gap between theoretical modeling and industrial-scale implementation. This study introduces a Dynamic Data Reconciliation approach based on the Extended Kalman Filter (EKF), designed to enhance the accuracy and internal consistency of key process variables. In contrast to steady-state reconciliation, the EKF-DDR explicitly incorporates process dynamics, system uncertainties, and periodic carbon transfer, allowing robust reconciliation of dynamic plant data. The framework was tested in two stages: first on a simulated dataset with known ground truth and added noise, and then on a 163-day industrial dataset. In simulation, the EKF-DDR reduced RMSE by up to 76%, validating its noise-rejection and state-recovery capability. When applied to plant data, it achieved variance reduction indices above 0.49 and improved adherence to mass balance constraints, lowering gold accounting imbalances from 12.63% to 5.13%. These results demonstrate that EKF-DDR not only suppresses random disturbances but also restores physical consistency across process phases, providing high-quality reconciled data for modeling, soft sensing, and advanced process control in CIL operations.
Mineral Processing
Zaheer Ahmed; Muhammad Bilal; Zulfiqar Ali; Muhammad Badar Hayat; Kazutoshi HAGA; Atsushi Shibayama
Abstract
Low-grade copper–gold porphyry ores present significant processing challenges due to poor mineral dissemination and high gangue content. In this study, a representative ore sample from the Saindak Copper–Gold Project, Pakistan, with an average copper grade of 0.4 wt%, was investigated to ...
Read More
Low-grade copper–gold porphyry ores present significant processing challenges due to poor mineral dissemination and high gangue content. In this study, a representative ore sample from the Saindak Copper–Gold Project, Pakistan, with an average copper grade of 0.4 wt%, was investigated to optimize flotation parameters for improved copper recovery. Mineralogical characterization using XRD, XRF, SEM–EDS, and ICP-OES confirmed chalcopyrite as the primary copper-bearing mineral finely disseminated within silicate gangue and iron sulfides. A series of batch flotation experiments were conducted by systematically varying particle size, slurry pH, collector dosage, and flotation time. The results showed that optimal conditions (particle size <75 μm, pH 12, and 1-min flotation time) enabled selective chalcopyrite recovery. Optimal flotation performance was achieved at pH 12 with a collector dosage of 5 g/t and a flotation time of 1 min, yielding a copper recovery of approximately 93% and a concentrate grade of 23 wt% under multistage flotation conditions. Flotation kinetics analysis indicated that the first-order kinetic model provided the best fit to the experimental data. The findings demonstrate that efficient copper upgrading from low-grade Saindak ore can be achieved with minimal collector consumption, offering a potentially cost-effective and sustainable processing strategy for similar porphyry copper deposits.
Environment
Asghar Azadehranjbar; Shahrzad khoramnejadian; Saeidreza Asemi Zavareh; Alireza Pendashteh
Abstract
Mining and minerals extraction and purification are critical in today’s world. However, these processes may have negative consequences on the environment. Xanthates which are essential in the floatation process are found to be significant polluting chemicals. In this manuscript, the effect of different ...
Read More
Mining and minerals extraction and purification are critical in today’s world. However, these processes may have negative consequences on the environment. Xanthates which are essential in the floatation process are found to be significant polluting chemicals. In this manuscript, the effect of different parameters on the recovery of lead from Nakhlak lead mine was investigated considering the impact of used chemicals on the surrounding environment including air, soil and native plant species. The reason for this investigation was to achieve the optimal conditions for the minimum consumption of xanthates and other chemicals. The optimal recovery was obtained in the presence of xanthate (1 kg/t) and sodium silicate (0.4 kg/t). In addition, MIBC showed to be more efficient in the floatation process. Furthermore, it was observed that higher xanthate contents are required for the floatation of large particles. Therefore, smaller particles of feed can decrease xanthate consumption. A particle size of 100 µm showed the best floatation recovery with the least xanthate requirement.