Document Type : Original Research Paper

Authors

Department of Civil Engineering, Malaviya National Institute of Technology, Jaipur, Rajasthan, India

10.22044/jme.2024.14410.2710

Abstract

India is a leading producer and exporter of dimensional marble. The processing of marble into dimensional and finished forms involves sawing, grinding, and polishing, generating significant quantities of Marble Processing Waste (MPW). Efforts for bulk recycling of MPW from the rapidly expanding marble industry are essential due to significant environmental impacts, hindered by limited inclusion rates and complex processing requirements in current practices. Concurrently, the increased demand for geotechnical fill materials and the depletion of natural soils necessitates sustainable alternatives. Using MPW in geotechnical fills offers a viable solution, yet it lacks comprehensive characterization. The aim of this study is to evaluate MPW as a sustainable alternative to conventional geotechnical fill materials. In this study, a comprehensive analysis of MPW's physical, geotechnical, and electrochemical properties, along with its mineralogical, elemental, and chemical composition, was conducted. The findings show that MPW, being non-plastic and non-swelling with a grain size distribution and hydraulic conductivity similar to silty sands, can be used directly from disposal sites without further processing. Notably, MPW achieves a maximum dry density of 1.84 g/cm³ and exhibits internal friction angles of 36.5°, ensuring stability. Electrochemical analysis indicates low leachability risks, with pH levels of 8.1 and electrical resistivity of 6,200 ohm-cm. Scanning Electron Microscopy images reveal that MPW particles are irregular, with considerable angularity and surface roughness. These results position MPW as a viable and environmentally friendly alternative to conventional fill materials, with the potential to significantly reduce the exploitation of natural resources and advance sustainable waste management practices.

Keywords

Main Subjects

  • Ritchie, H., Samborska, V., & Roser, M. (2024). Urbanization. Our world in data.
  • Ekhaese, E. N., & Ndimako, O. O. (2023). Eco-friendly construction materials and health benefits in the design of an all-inclusive health resorts, Nigeria. Frontiers in Built Environment9, 1011759.
  • Montani, C. (2021). XXXII Rapporto Marmo e Pietre nel Mondo 2021 [XXXII Report on Marble and Stones in the World 2021]. Aldus Casa di Edizioni in Carrara. Available online: https://www.worldstonereport.com/ (Accessed on 18-07-2024).
  • ASTM International. (2022). Standard terminology relating to dimension stone (ASTM Standard No. C119-22).
  • Indian Bureau of Mines. (2021). Indian Minerals Yearbook 2020 (59th ed.), Minor Minerals 30.15 Marble (Advance Release).
  • Indian Bureau of Mines. (2018). Indian Minerals Yearbook 2017 (56th ed.), Minor Minerals 30.15 Marble (Advance Release).
  • International Labour Organization. (2021). Challenges and opportunities for productive employment and decent work in the natural stone mining industry supply chain in Rajasthan. ISBN 978-92-2-034393-7. Retrieved from https://www.ilo.org/publications/challenges-and-opportunities-productive-employment-and-decent-work-natural
  • Mendoza, J. M. F., Feced, M., Feijoo, G., Josa, A., Gabarrell, X., & Rieradevall, J. (2014). Life cycle inventory analysis of granite production from cradle to gate. The International Journal of Life Cycle Assessment19, 153-165. https://doi.org/10.1007/s11367-013-0637-6
  • Alhaj, J. (2013, October). Effects of the thickness of block cutting machine gang saw on waste percentages and productivity. In Third International Conference on Energy and Environmental Protection in Sustainable Development (ICEEP III).
  • Strzałkowski, P. (2021). Characteristics of waste generated in Dimension Stone processing. Energies14(21), 7232.
  • Yurdakul, M. (2020). Natural stone waste generation from the perspective of natural stone processing plants: An industrial-scale case study in the province of Bilecik, Turkey. Journal of Cleaner Production276, 123339.
  • Jalalian, M. H., Bagherpour, R., & Khoshouei, M. (2021). Wastes production in dimension stones industry: resources, factors, and solutions to reduce them. Environmental Earth Sciences80(17), 560.
  • Rana, A., Kalla, P., Verma, H. K., & Mohnot, J. K. (2016). Recycling of dimensional stone waste in concrete: A review. Journal of cleaner production135, 312-331.
  • El Haggar, S. (2010). Sustainable industrial design and waste management: cradle-to-cradle for sustainable development. Academic Press.
  • Gülmez, N. (2022). Experimental and material characterization of composites, including waste iron and marble powder. Environmental Science and Pollution Research29(34), 51927-51941.
  • Piccini, L., Di Lorenzo, T., Costagliola, P., & Galassi, D. M. P. (2019). Marble slurry’s impact on groundwater: the case study of the Apuan Alps Karst Aquifers. Water11(12), 2462.
  • Rathore, K. K., & Singh, S. K. (2021). Ground Water Quality Assessment of Marble Mining Areas in Rajsamand District, Rajasthan, India. Current World Environment16(2), 551.
  • Central Pollution Control Board. (2012). Disposal options of marble slurry in Rajasthan. Central Pollution Control Board Zonal Office (Central), Bhopal. Available online: https://cpcb.nic.in/openpdffile.php?id=UmVwb3J0RmlsZXMvMjg3XzE0NzEzMzkwNzVfRGlzcG9zYWwgT3B0aW9ucyBvZiBNYXJibGUgU2x1cnJ5IGluIFJhamFzdGhhbi5wZGY (Accessed on 18-07-2024).
  • India Environment Portal. (2022, June 04). Joint committee report on unscientific dumping of marble slurry on agricultural land, Harischandrapuram railway station, Kotabommali mandal, Srikakulam district, Andhra Pradesh. Available online: http://www.indiaenvironmentportal.org.in/content/472910/joint-committee-report-on-unscientific-dumping-of-marble-slurry-on-agricultural-land-harischandrapuram-railway-station-kotabommali-mandal-srikakulam-district-andhra-pradesh-04062022/ (Accessed on 18-07-2024).
  • India Environment Portal. (2023, February 22). Order of the National Green Tribunal regarding dumping of marble and granite waste in the storm water drain of Mohi village, district Rajasmand, Rajasthan. Available online: http://admin.indiaenvironmentportal.org.in/content/dumping-marble-and-granite-waste-storm-water-drain-mohi-village-district-rajasmand (Accessed on 18-07-2024).
  • Tripura, D. D., Lohar, J., & Pardhasaradhi, K. (2021). Characteristic properties of natural aggregate incorporated fibre reinforced compressed earth blocks. In Indian Geotechnical Conference(pp. 1-17). Singapore: Springer Nature Singapore.
  • Chandra, S., Sangma, S., Tripura, D. D., & Lohar, J. (2023). Structural Performance of Reinforced and Un-reinforced Earth Block Masonry Under Compressive, Flexural and Diagonal Compressive Loads. In Structural Engineering Convention(pp. 433-441). Singapore: Springer Nature Singapore.
  • Lohar, J., Shrivastava, N., & Sharma, A. (2023). Feasibility of granite processing waste as a fill material in geotechnical applications. Materials Today: Proceedings.
  • Sharma, A., Shrivastava, N., & Lohar, J. (2023). Construction & demolition waste in geotechnical applications: a review. Materials Today: Proceedings.
  • Sharma, A., Shrivastava, N., & Lohar, J. (2023). Assessment of geotechnical and geo-environmental behaviour of recycled concrete aggregates, recycled brick aggregates and their blends. Cleaner Materials7, 100171. 1
  • Natani, J. V., & Raghav, K. S. (2003). Environmental impact of marble mining around Makrana, Nagaur district, Rajasthan. Geological Society of India62(3), 369-376.
  • Sivrikaya, O., Kıyıldı, K. R., & Karaca, Z. (2014). Recycling waste from natural stone processing plants to stabilise clayey soil. Environmental Earth Sciences71, 4397-4407.
  • Chouhan, H. S., Kalla, P., Nagar, R., & Gautam, P. K. (2019). Influence of dimensional stone waste on mechanical and durability properties of mortar: A review. Construction and Building Materials227, 116662.
  • Salem, H. S. (2021). Evaluation of the Stone and Marble Industry in Palestine: environmental, geological, health, socioeconomic, cultural, and legal perspectives, in view of sustainable development. Environmental Science and Pollution Research28(22), 28058-28080.
  • Singhal, A., & Goel, S. (2022). Impact of Sandstone Quarrying on the Health of Quarry Workers and local residents: a case study of Keru, Jodhpur, India. In Treatment and disposal of solid and hazardous wastes(pp. 97-118). Cham: Springer International Publishing.
  • Sain, A., Gaur, A., Somani, P., & Balotiya, G. (2024). Bambusa balcooa bamboo-reinforced concrete beams: experimental and FEM investigation for energy-efficient pavement construction. Environmental Science and Pollution Research, 1-16.
  • Balotiya, G., Gaur, A., Somani, P., & Sain, A. (2023). Investigating mechanical and durability aspects of concrete incorporating Wollastonite and bottom ash. Materials Today: Proceedings.
  • Sain, A., Gaur, A., Somani, P., Khichad, J. S., & Balotiya, G. (2024). Characterization and Evaluation of Bamboo Species for Construction Applications Incorporating TOPSIS, AHP and VIKOR. Arabian Journal for Science and Engineering, 1-17.
  • Kumar, A., Somani, P., Sain, A., & Gaur, A. (2023). Enhancing thermal behaviour of concrete pavement by incorporating vermiculite. Materials Today: Proceedings93, 346-356.
  • Pappu, A., Chaturvedi, R., & Tyagi, P. (2020). Sustainable approach towards utilizing Makrana marble waste for making water resistant green composite materials. SN Applied Sciences2, 1-12.
  • Fawad, M., Ullah, F., Shah, W., Jawad, M., Khan, K., & Rashid, W. (2022). An integrated approach towards marble waste management: GIS, SFA, and recycling options. Environmental Science and Pollution Research29(56), 84460-84470.
  • Khalil, M., Hanif, M. A., Rashid, U., Ahmad, J., Alsalme, A., & Tsubota, T. (2023). Low-cost novel nano-constructed granite composites for removal of hazardous Terasil dye from wastewater. Environmental Science and Pollution Research30(34), 81333-81351.
  • Khichad, J. S., & Vishwakarma, R. J. (2024). Overview and Discussion of Pavement Performance Prediction Techniques for Maintenance and Rehabilitation Decision-Making. International Journal of Pavement Research and Technology, 1-17.
  • Singh, S., Soti, A., Kulshreshtha, N. M., Samaria, A., Brighu, U., Gupta, A. B., & Bezbaruah, A. N. (2024). Machine Learning Application for Nutrient Removal Rate Coefficient Analyses in Horizontal Flow Constructed Wetlands. ACS ES&T Water4(6), 2619-2631.
  • Yaylacı, M., Öner, E., Adıyaman, G., Öztürk, Ş., Uzun Yaylacı, E., & Birinci, A. (2023). Analyzing of continuous and discontinuous contact problems of a functionally graded layer: theory of elasticity and finite element method. Mechanics Based Design of Structures and Machines, 1-19.
  • Özdemir, M. E., & Yaylac, M. (2023). Research of the impact of material and flow properties on fluid-structure interaction in cage systems. Wind and structures36(1), 31.
  • Yaylacı, M., Şabano, B. Ş., Özdemir, M. E., & Birinci, A. (2022). Solving the contact problem of functionally graded layers resting on a HP and pressed with a uniformly distributed load by analytical and numerical methods. Structural Engineering and Mechanics, An Int'l Journal82(3), 401-416.
  • Yaylaci, E. U., Yaylaci, M., Ozdemir, M. E., Terzi, M., & Ozturk, S. (2023). Analyzing the mechano-bactericidal effect of nano-patterned surfaces by finite element method and verification with artificial neural networks. Advances in nano research15(2), 165-174.
  • Yaylacı, M., Yaylacı, E. U., Özdemir, M. E., Öztürk, Ş., & Sesli, H. (2023). Vibration and buckling analyses of FGM beam with edge crack: Finite element and multilayer perceptron methods.
  • Ahmad, S., & Khan, N. (2019). Marble industry role in the socio-economic development of marble industrial owners of district Mohmand federal administered tribal area-Pakistan.  Eng. Lett9(3), 10-7176.
  • Melodi, M. M., & Ogunyemi, O. B. (2019). Socio-economic impact of granite stone quarry engagement on workers’ livelihood in Ondo and Edo States, Nigeria. ABUAD Journal of Engineering Research and Development2(2), 10-15.
  • Careddu, N. (2019). Dimension stones in the circular economy world. Resources Policy60, 243-245. https://doi.org/10.1016/J.RESOURPOL.2019.01.012
  • Marshall, S., Taylor, K., Connor, T., Haines, F., & Tödt, S. (2022). Will Business and Human Rights regulation help Rajasthan's bonded labourers who mine sandstone?. Journal of Industrial Relations64(2), 248-271.
  • Times of India (2016, May 27). Thousands of stone quarries closed as NGT deadline nears. Available online: https://timesofindia.indiatimes.com/home/environment/thousands-of-stone-quarries-closed-as-ngt-deadline-nears/articleshow/52468091.cms (Accessed on 18-07-2024).
  • Yaylacı, M. (2016). The investigation crack problem through numerical analysis. Structural Engineering and Mechanics, An Int'l Journal57(6), 1143-
  • Yaylacı, M., Uzun Yaylacı, E., Özdemir, M. E., Ay, S., & Özturk, S. (2022). Implementation of finite element and artificial neural network methods to analyze the contact problem of a functionally graded layer containing crack.
  • Yaylaci, M. (2022). Simulate of edge and an internal crack problem and estimation of stress intensity factor through finite element method. Advances in nano research12(4), 405-414.
  • Yaylacı, M., Abanoz, M., Yaylacı, E. U., Ölmez, H., Sekban, D. M., & Birinci, A. (2022). Evaluation of the contact problem of functionally graded layer resting on rigid foundation pressed via rigid punch by analytical and numerical (FEM and MLP) methods. Archive of Applied Mechanics92(6), 1953-1971.
  • Adıyaman, G., Öner, E., Yaylacı, M., & Birinci, A. (2023). A study on the contact problem of a layer consisting of functionally graded material (FGM) in the presence of body force. Journal of Mechanics of Materials and Structures18(1), 125-141.
  • Yaylaci, M., Abanoz, M., Yaylaci, E. U., Olmez, H., Sekban, D. M., & Birinci, A. (2022). The contact problem of the functionally graded layer resting on rigid foundation pressed via rigid punch. Steel and Composite Structures43(5), 661.
  • Öner, E., Şengül Şabano, B., Uzun Yaylacı, E., Adıyaman, G., Yaylacı, M., & Birinci, A. (2022). On the plane receding contact between two functionally graded layers using computational, finite element and artificial neural network methods. ZAMM‐Journal of Applied Mathematics and Mechanics/Zeitschrift für Angewandte Mathematik und Mechanik102(2), e202100287.
  • Yaylaci, M., Abanoz, M., Yaylaci, E. U., Olmez, H., Sekban, D. M., & Birinci, A. (2022). The contact problem of the functionally graded layer resting on rigid foundation pressed via rigid punch. Steel and Composite Structures43(5), 661.
  • YayIaci, M., YayIaci, E. U., Ozdemir, M. E., Ay, S., & Ozturk, Ş. (2022). Implementation of finite element and artificial neural network methods to analyze the contact problem of a functionally graded layer containing crack. Steel and Composite Structures45(4), 501.
  • Tomar, A., Lohar, J., & Shrivastava, N. (2024, June). Parametric Study of Mechanically Stabilised Earth Wall using PLAXIS. In IOP Conference Series: Earth and Environmental Science(Vol. 1326, No. 1, p. 012126). IOP Publishing.
  • Singh, M., Srivastava, A., & Bhunia, D. (2017). An investigation on effect of partial replacement of cement by waste marble slurry. Construction and Building Materials134, 471-488.
  • Amin, S. K., Allam, M. E., Garas, G. L., & Ezz, H. (2020). A study of the chemical effect of marble and granite slurry on green mortar compressive strength. Bulletin of the National Research Centre44, 1-5.
  • Mármol, I., Ballester, P., Cerro, S., Monrós, G., Morales, J., & Sánchez, L. (2010). Use of granite sludge wastes for the production of coloured cement-based mortars. Cement and Concrete Composites32(8), 617-622.
  • Singhal, V., Nagar, R., & Agrawal, V. (2020). Sustainable use of fly ash and waste marble slurry powder in concrete. Materials Today: Proceedings32, 975-981.
  • Rana, A., Kalla, P., & Csetenyi, L. J. (2015). Sustainable use of marble slurry in concrete. Journal of cleaner production94, 304-311.
  • Sadek, D. M., El-Attar, M. M., & Ali, H. A. (2016). Reusing of marble and granite powders in self-compacting concrete for sustainable development. Journal of Cleaner Production121, 19-32.
  • Bakshi, P., Pappu, A., Patidar, R., Gupta, M. K., & Thakur, V. K. (2020). Transforming marble waste into high-performance, water-resistant, and thermally insulative hybrid polymer composites for environmental sustainability. Polymers12(8), 1781.
  • Ahmad, S., Hassan Shah, M. U., Ullah, A., Shah, S. N., Rehan, M. S., Khan, I. A., & Ahmad, M. I. (2021). Sustainable use of marble waste in industrial production of fired clay bricks and its employment for treatment of flue gases. ACS omega6(35), 22559-22569. https://doi.org/10.1021/ACSOMEGA.1C02279
  • Bilgin, N., Yeprem, H. A., Arslan, S. Ö. N. M. E. Z., Bilgin, A., Günay, E., & Marşoglu, M. (2012). Use of waste marble powder in brick industry. Construction and Building Materials29, 449-457.
  • Ranjan, S., & Sharma, T. (2023, February). Evaluating the properties of compressed soil earth blocks after the addition of bagasse ash, marble powder and paddy straw. In IOP Conference Series: Earth and Environmental Science(Vol. 1110, No. 1, p. 012005). IOP Publishing.
  • Jassim, N. W., Hassan, H. A., Mohammed, H. A., & Fattah, M. Y. (2022). Utilization of waste marble powder as sustainable stabilization materials for subgrade layer. Results in Engineering14, 100436.
  • Kolli, S., Haq, A. U., Dammala3&4, P. K., Janga, J. K., & Reddy, K. R. (2023). Sustainable Use of Marble Byproduct for Stabilizing Migrating Sand Dunes in Thar Desert, India.
  • Soğancı, A. S., Yenginar, Y., & Orman, A. (2023). Geotechnical properties of clayey soils stabilized with marble dust and granulated blast furnace slag. KSCE Journal of Civil Engineering27(11), 4622-4634.
  • Jain, A. K., & Jha, A. K. (2020). Geotechnical behaviour and micro-analyses of expansive soil amended with marble dust. Soils and Foundations60(4), 737-751.
  • Yaylacı, E. U., Öner, E., Yaylacı, M., Özdemir, M. E., Abushattal, A., & Birinci, A. (2022). Application of artificial neural networks in the analysis of the continuous contact problem. Structural Engineering and Mechanics, An Int'l Journal84(1), 35-48.
  • Turan, M., Uzun Yaylacı, E., & Yaylacı, M. (2023). Free vibration and buckling of functionally graded porous beams using analytical, finite element, and artificial neural network methods. Archive of Applied Mechanics93(4), 1351-1372.
  • Yaylacı, M., Şabano, B. Ş., Özdemir, M. E., & Birinci, A. (2022). Solving the contact problem of functionally graded layers resting on a HP and pressed with a uniformly distributed load by analytical and numerical methods. Structural Engineering and Mechanics, An Int'l Journal82(3), 401-416.
  • Yaylaci, M., Abanoz, M., Yaylaci, E. U., Olmez, H., Sekban, D. M., & Birinci, A. (2022). The contact problem of the functionally graded layer resting on rigid foundation pressed via rigid punch. Steel and Composite Structures43(5), 661.
  • Yaylacı, M., Abanoz, M., Yaylacı, E. U., Ölmez, H., Sekban, D. M., & Birinci, A. (2022). Evaluation of the contact problem of functionally graded layer resting on rigid foundation pressed via rigid punch by analytical and numerical (FEM and MLP) methods. Archive of Applied Mechanics92(6), 1953-1971.
  • Pant, A., Datta, M., & Ramana, G. V. (2019). Bottom ash as a backfill material in reinforced soil structures. Geotextiles and Geomembranes47(4), 514-521.
  • Pant, A., Ramana, G. V., Datta, M., & Gupta, S. K. (2019). Coal combustion residue as structural fill material for reinforced soil structures. Journal of Cleaner Production232, 417-426.
  • Pant, A., Datta, M., Ramana, G. V., & Mahanta, A. (2019, March). Utilization of pond ash as structural fill material in reinforced soil structures. In Eighth International Conference on Case Histories in Geotechnical Engineering(pp. 293-302). Reston, VA: American Society of Civil Engineers.
  • Prasad, P. S., & Ramana, G. V. (2016). Feasibility study of copper slag as a structural fill in reinforced soil structures. Geotextiles and Geomembranes44(4), 623-640.
  • Prasad, P. S., & Ramana, G. V. (2016). Imperial smelting furnace (zinc) slag as a structural fill in reinforced soil structures. Geotextiles and Geomembranes44(3), 406-428.
  • Bhoi, A. K., Mandal, J. N., & Juneja, A. (2020). Feasibility Study of Bagasse Ash as a Filling Material. In Advancements in Unsaturated Soil Mechanics: Proceedings of the 3rd GeoMEast International Congress and Exhibition, Egypt 2019 on Sustainable Civil Infrastructures–The Official International Congress of the Soil-Structure Interaction Group in Egypt (SSIGE)(pp. 81-94). Springer International Publishing.
  • Soleimanbeigi, A., Tanyu, B. F., Aydilek, A. H., Florio, P., Abbaspour, A., Dayioglu, A. Y., & Likos, W. J. (2019). Evaluation of recycled concrete aggregate backfill for geosynthetic-reinforced MSE walls. Geosynthetics International26(4), 396-412.
  • Mkahal, Z., Mamindy-Pajany, Y., Maherzii, W., & Abriak, N. E. (2022). Recycling of mineral solid wastes in backfill road materials: technical and environmental investigations. Waste and Biomass Valorization13(1), 667-687.
  • Bizjak, K. F., Likar, B., & Lenart, S. (2021). Using recycled material from the paper industry as a backfill material for retaining walls near railway lines. Sustainability13(2), 979. https://doi.org/10.3390/su13020979
  • Sharma, A., Shrivastava, N., & Lohar, J. (2023). Assessment of geotechnical and geo-environmental behaviour of recycled concrete aggregates, recycled brick aggregates and their blends. Cleaner Materials7, 100171.
  • Lohar, J., Shrivastava, N., & Sharma, A. (2023). Feasibility of granite processing waste as a fill material in geotechnical applications. Materials Today: Proceedings.
  • Venkatachalam, M. N., & Balu, S. (2022). A review on the application of industrial waste as reinforced earth fills in mechanically stabilized earth retaining walls. Environmental Science and Pollution Research29(57), 86277-86297.
  • Wagale, M., Dandin, S., Bokil, S., & Sathe, S. (2024). Potential use of fly ash in structural fill application: a review. Environmental Science and Pollution Research31(1), 90-108.
  • Samtani, N. C., & Nowatzki, E. A. (2021). Mechanically Stabilized Earth (MSE) Wall Fills: A Framework for Use of Local Available Sustainable Resources (LASR) Publication No. FHWA-HIN-21-002.
  • Benjeddou, O., & Alwetaishi, M. (2021). Valorization of powder obtained from marble sludge waste and its suitability as a mineral filler. Crystals11(6), 619.
  • Medina, G., Del Bosque, I. S., Frías, M., De Rojas, M. S., & Medina, C. (2017). Mineralogical study of granite waste in a pozzolan/Ca (OH) 2 system: Influence of the activation process. Applied Clay Science135, 362-371.
  • (2016). Indian Minerals Yearbook 2014 (Part-III: Mineral Reviews) 53rd Edition Marble (Final Release) Government of India Ministry of Mines Indian Bureau Of Mines.
  • Indian Road Congress (2010). IRC 36: Recommended Practice for Construction of Earth Embankments and Sub-Grade for Road Works (First Revision).
  • Indian Road Congress (IRC). (2014). IRC SP 102: Guidelines for Design and Construction of Reinforced Soil Walls.
  • Berg, R. R., Christopher, B. R., & Samtani, N. C. (2009). Design of Mechanically Stabilized Earth Walls and Reinforced Soil Slopes – Volume I (FHWA-NHI-10-024).
  • British Standards Institution. (2010). Code of Practice for Strengthened/reinforced Soils and Other Fills: BS 8006-1: 2010.
  • Indian Road Congress (IRC). (2001). IRC SP 58: Guidelines for Use of Fly Ash in Road Embankments (Reprinted: August, 2009).
  • Yoon, S., Balunaini, U., Yildirim, I. Z., Prezzi, M., & Siddiki, N. Z. (2009). Construction of an embankment with a fly and bottom ash mixture: Field performance study. Journal of Materials in Civil Engineering21(6), 271-278.
  • Kumar, K. B., Krishna, G., & Umashankar, B. (2019, March). Evaluation of waste foundry sand and blast furnace steel slag as geomaterials. In Eighth International Conference on Case Histories in Geotechnical Engineering(pp. 304-313). Reston, VA: American Society of Civil Engineers.
  • Santos, E. C. G., Palmeira, E. M., & Bathurst, R. J. (2014). Performance of two geosynthetic reinforced walls with recycled construction waste backfill and constructed on collapsible ground. Geosynthetics International21(4), 256-269.
  • Kumar, K. P. (2020). Interaction studies of different geogrids in nonconventional fill materials(Doctoral dissertation, Swinburne University).
  • Sun, J. S., Dou, Y. M., Yang, C. F., & Sun, J. C. (2009, August). Study on the application performances of saponated residue and fly ash mixture as geogrids reinforced earth retaining wall filling material. In Slope Stability, Retaining Walls, and Foundations: Selected Papers from the 2009 GeoHunan International Conference(pp. 197-201).
  • Santos, E. C., Palmeira, E. M., & Bathurst, R. J. (2013). Behaviour of a geogrid reinforced wall built with recycled construction and demolition waste backfill on a collapsible foundation. Geotextiles and Geomembranes39, 9-19.
  • Bureau of Indian Standards. (1980). IS 2720-3-2: Methods of test for soils, Part 3: Determination of specific gravity, Section 2: Fine, medium, and coarse-grained soils.
  • Bureau of Indian Standards. (1985). IS 2720-4: Methods of test for soils, Part 4: Grain size analysis.
  • Bureau of Indian Standards. (1985). IS 2720-5: Methods of test for soils, Part 5: Determination of liquid and plastic limit.
  • Bureau of Indian Standards. (1977). IS 2720-40: Methods of test for soils, Part 40: Determination of free swell index of soils.
  • Bureau of Indian Standards. (1983). IS 2720-8: Methods of test for soils, Part 8: Determination of water content-dry density relation using heavy compaction.
  • Bureau of Indian Standards. (1986). IS 2720-17: Methods of test for soils, Part 17: Laboratory determination of permeability.
  • Bureau of Indian Standards. (1977). IS 2720-39-1: Methods of test for soils, Part 39: Direct shear test for soils containing gravel, Section 1: Laboratory test.
  • United States Environmental Protection Agency (USEPA). (2004). SW-846 Test Method 9045D: Soil and Waste pH.
  • Bureau of Indian Standards. (1972). IS 2720-22: Methods of test for soils, Part 22: Determination of organic matter.
  • Jha, A. K., Jain, A. K., & Akhtar, M. P. (2023). Evaluating the Behavior of Marble Dust–Bentonite as an Alternative to Sand–Bentonite Mixes Permeated with Electrolyte Concentrations. Journal of Hazardous, Toxic, and Radioactive Waste27(1), 04022035.
  • Blaud, A., Menon, M., van der Zaan, B., Lair, G. J., & Banwart, S. A. (2017). Effects of dry and wet sieving of soil on identification and interpretation of microbial community composition. Advances in agronomy142, 119-142.
  • Ministry of Road Transport and Highways of India (MoRTH). (2013). MoRTH 2013 Specifications for Road and Bridge. Indian Roads Congress.
  • National Concrete Masonry Association (NCMA). (2012). Design Manual for Segmental Retaining Walls. National Concrete Masonry Association, 3rd Edition.
  • Federal Highway Administration (FHWA). (2021). Mechanically Stabilized Earth (MSE) Wall Fills - A Framework for Use of Local Available Sustainable Resources (LASR).
  • Havangi, V., Sinha, A., Paravathi, G., & Chandra, S. (2017). Municipal solid waste in road embankment construction-a case study. Journal of the Indian Roads Congress, 78(2), 79–90.
  • Kandolkar, S. S., & Mandal, J. N. (2016). Behavior of reinforced-stone dust walls with backfill at varying relative densities. Journal of Hazardous, Toxic, and Radioactive Waste20(1), 04015010.
  • Kandolkar, S. S., & Mandal, J. N. (2014). Effect of reinforcement on stress–strain behavior of stone dust. International Journal of Geotechnical Engineering8(4), 383-395.
  • Karnamprabhakara, B. K., Balunaini, U., Arulrajah, A., & Evans, R. (2023). Evaluation of interaction properties of uniaxial geogrids with waste foundry sand. Geosynthetics International30(2), 169-183.
  • Karnamprabhakara, B. K., Balunaini, U., Arulrajah, A., & Evans, R. (2021). Axial pullout resistance and interface direct shear properties of geogrids in pond ash. International Journal of Geosynthetics and Ground Engineering7(2), 22.
  • Vieira, C. S. (2020). Valorization of fine-grain construction and demolition (C&D) waste in geosynthetic reinforced structures. Waste and biomass valorization11(4), 1615-1626.
  • El Ghoraiby, M., Park, H., & Manzari, M. T. (2020). Physical and mechanical properties of Ottawa F65 sand. In Model tests and numerical simulations of liquefaction and lateral spreading: LEAP-UCD-2017(pp. 45-67). Springer International Publishing.
  • Jumikis, A. (1962). Soil mechanics. D. Van Norstrand Company.  Yew Yourk, NY.
  • Bureau of Indian Standards. (1970). IS 1498: Classification and identification of soils for general engineering purposes.
  • Ministry of Rural Development (MoRD). (2014). Specifications for rural roads. Indian Roads Congress.
  • American Association of State Highway and Transportation Officials (AASHTO). (2002). Standard Specifications for Highway Bridges (17th Edition).
  • Gupta, R. K., & Gupta, R. K. (2018, June). Cutting tool for marble & granite: a review. In IOP Conference Series: materials science and engineering(Vol. 377, No. 1, p. 012126). IOP Publishing.
  • Pillai, A. G., & Gali, M. L. (2022). Role of particle shape on the shear strength of sand-GCL interfaces under dry and wet conditions. Geotextiles and Geomembranes50(2), 262-281.
  • Holtz, R. D., Kovacs, W. D., & Sheahan, T. C. (1981). An introduction to geotechnical engineering(Vol. 733). Englewood Cliffs, NJ: Prentice-Hall.
  • Vardhan, K., Siddique, R., & Goyal, S. (2019). Influence of marble waste as partial replacement of fine aggregates on strength and drying shrinkage of concrete. Construction and Building Materials228, 116730. https://doi.org/10.1016/j.conbuildmat.2019.116730
  • Soliman, N. M. (2013). Effect of using marble powder in concrete mixes on the behavior and strength of RC slabs. International Journal of Current Engineering and Technology3(5), 1863-1870.
  • Jain, A. K., Jha, A. K., & Akhtar, P. M. (2022). Assessing the swelling and permeability behavior of novel marble dust–bentonite with sand–bentonite mixes for use as a landfill liner material. Indian Geotechnical Journal52(3), 675-690.
  • Zorluer, I., & Demirbas, A. (2013). Use of marble dust and fly ash in stabilization of base material. Science and Engineering of Composite Materials20(1), 47-55.
  • Kumar, K. B., Krishna, G., & Umashankar, B. (2019, March). Evaluation of waste foundry sand and blast furnace steel slag as geomaterials. In Eighth International Conference on Case Histories in Geotechnical Engineering(pp. 304-313). Reston, VA: American Society of Civil Engineers.
  • Barna, R., Bae, H. R., Méhu, J., van der Sloot, H., Moszkowicz, P., & Desnoyers, C. (2000). Assessment of chemical sensitivity of Waelz slag. Waste Management20(2-3), 115-124.
  • Lee, T. (2011). Leaching characteristics of bottom ash from coal fired electric generating plants, and waste tire; individually and mixtures when used as construction site fill materials. Waste management31(2), 246-252.
  • Heaney, M. B. (2003). Electrical conductivity and resistivity. Electrical measurement, signal processing, and displays7(1).
  • Zohra-Hadjadj, F., Laredj, N., Maliki, M., Missoum, H., & Bendani, K. (2019). Laboratory evaluation of soil geotechnical properties via electrical conductivity. Revista Facultad de Ingeniería Universidad de Antioquia, (90), 101-112.
  • Andrade, R. (2011). Intervention of Electrical Resistance Tomography (ERT) in resolving hydrological problems of a semi arid granite terrain of Southern India. Journal of the Geological Society of India78, 337-344.
  • Palacky, G. J. (1988). Resistivity Characteristics of Geologic Targets. Electromagnetic Methods in Applied Geophysics2(3), 53.
  • County, L. (2009). Special Provisions for Segmental Retaining Wall (SP-090005). The IOWA Department of Transportation Standard Specifications.
  • Marr, W. A., & Stulgis, R. P. (2013). Selecting backfill materials for MSE retaining walls: Final report prepared for NCHRP Transportation Research Board of the National Academies. Transportation Research Board. Available online: https://trid.trb.org/view/809124 (Accessed on 18-07-2024).
  • Huang, P.-T., Patel, M., Santagata, M. C., & Bobet, A. (2009). FHWA/IN/JTRP-2008/2 Final report: Classification of organic soils. Purdue University. Available online: https://docs.lib.purdue.edu/jtrp/94/ (Accessed on 18-07-2024).