M.A. Chamanzad; M. Nikkhah
Abstract
Drilling and blasting have numerous applications in the civil and mining engineering. Due to the two major components of rock masses, namely the intact rock matrix and the discontinuities, their behavior is a complicated process to be analyzed. The purpose of this work is to investigate the effects of ...
Read More
Drilling and blasting have numerous applications in the civil and mining engineering. Due to the two major components of rock masses, namely the intact rock matrix and the discontinuities, their behavior is a complicated process to be analyzed. The purpose of this work is to investigate the effects of the geomechanical and geometrical parameters of rock and discontinuities on the rock mass blasting using the UDEC software. To this end, a 2D distinct element code (DEM) code is used to simulate the stress distribution around three blast holes in some points and propagation of the radial cracks caused by blasting. The critical parameters analyzed for this aim include the normal stiffness (JKN) and shear stiffness (JKS), spacing, angle and persistence of joint, shear and bulk modulus, density of rock, and borehole spacing. The results obtained show that the joint parameters and rock modulus have very significant effects, while the rock density has less a effect on the rock mass blasting. Also the stress level has a direct relationship with JKN, JKS, bulk modulus, and the shear modulus has an inverse relationship with the rock density. Moreover, the stress variation in terms of spacing and joint angle indicates sinusoidal and repetitive changes with the place of target point with respect to the blast hole and joint set. Also with a decrease in the JKN and JKS values, the radial cracked and plastic zones around a blast hole show more development. With increase in the joint persistence, the plastic zones decrease around a blast hole.
A. Siamaki; H. Bakhshandeh Amnieh
Abstract
A considerable amount of energy is released in the form of shock wave from explosive charge detonation. Shock wave energy is responsible for the creation of crushing and fracture zone around the blast hole. The rest of the shock wave energy is transferred to rock mass as ground vibration. Ground vibration ...
Read More
A considerable amount of energy is released in the form of shock wave from explosive charge detonation. Shock wave energy is responsible for the creation of crushing and fracture zone around the blast hole. The rest of the shock wave energy is transferred to rock mass as ground vibration. Ground vibration is conveyed to the adjacent structures by body and surface waves. Geological structures like faults, fractures, and fillings play important roles in the wave attenuation. Studying the mechanism of ground wave propagation from blasts gives a better understanding about the stress wave transmission and its effect on the near structures. In this research work, the stress wave transmissions from discontinuities and fillings were evaluated using a field measurement and a Universal Distinct Element Code (UDEC). A single-hole blast was conducted in the Kangir dam, and the resulting vibrations were measured in many points before and after the faults. Numerical simulation shows the effects of geo-mechanical properties of fillings on the reflection and refraction rate of the stress wave. There are more energy reflections in the rock boundaries and soil fillings, and more energy is absorbed by soil fillings compared with rock fillings. Furthermore, there is a close correlation between the ground vibration records for the Kangir dam and the numerical results. The maximum relative error between the actual records and the simulated ones was found to be 18.5%, which shows the UDEC ability for the prediction of blast vibrations.
Javad Gholamnejad; HamidReza Bahaaddini; Morteza Rastegar
Abstract
Static deformation modulus is recognized as one of the most important parameters governing the behavior of rock masses. Predictive models for the mechanical properties of rock masses have been used in rock engineering because direct measurement of the properties is difficult due to time and cost constraints. ...
Read More
Static deformation modulus is recognized as one of the most important parameters governing the behavior of rock masses. Predictive models for the mechanical properties of rock masses have been used in rock engineering because direct measurement of the properties is difficult due to time and cost constraints. In this method the deformation modulus is estimated indirectly from classification systems. This paper presents the results of a study into the application of Artificial Neural Networks (ANN) technique and Regression models for estimation of the deformation modulus of rock masses. A database, including 225 actual measured deformation modulus, Uniaxial Compressive Strengths of the rock (UCS), and Rock Mass Rating (RMR) was established. Data collected from different projects. For predicting Em by regression, a nonlinear regression method was chosen. This model showed the coefficient correlation of 0.751 and mean absolute percentage error (MAPE) of 9.911%. Also a three-layer ANN was found to be optimum, with an architecture of two neurons in the input layer, four neurons in the hidden layer and one neuron in the output layer. The correlation coefficient determined for deformation modulus predicted by the ANN was 0.786 and the quantity of MAPE was 6.324%. With respect to the results obtained from two models, the ANN technique was shown to be better than the regression model because of its higher accuracy.
