Exploitation
Assefa Hailesilasie Wolearegay; Yowhas Birhanu Amare; Asmelash Abay Hagos; Kassa Amare Mesfin; Hagos Abraha; Bereket Gebresilassie; Nageswara Rao Cheepurupalli; Yewuhalashet Fissha
Abstract
The Dichinama area in northern Ethiopia is a potential source of dimension stone, but the quality of the marble has been a major challenge for mining operations. This research aims to evaluate the quality of dimension stone by conducting a comprehensive study involving geological mapping, geotechnical ...
Read More
The Dichinama area in northern Ethiopia is a potential source of dimension stone, but the quality of the marble has been a major challenge for mining operations. This research aims to evaluate the quality of dimension stone by conducting a comprehensive study involving geological mapping, geotechnical testing, and geochemical analysis. The study collected nine rock samples from three active mining sites in the Dichinama area, analyzing properties such as density, water absorption, compressive strength, flexural strength, and abrasion resistance. Additionally, ten samples were collected for geochemical analysis, focusing on parameters like calcite, CaO values, LOI, SiO2 content, and other oxide concentrations. The geotechnical tests revealed that the properties of the marble in the Dichinama area were mainly calcite, with compressive strength values ranging from 29.6 to 74.5 MPa, flexural strength from 7 to 52.5 MPa, abrasion resistance from 8.3 to 17.2, density from 2257 to 2562 kg/m3, and water absorption from 0.12 to 0.93. However, most of these parameters fell below the minimum ASTM standards for marble dimension stone. The results suggest that these inferior characteristics negatively affect the recovery and quality of the dimension stone.
Mineral Processing
Ali Nikouei Mahani; Mohammad Karamoozian; Mohammad Jahani Chegeni; Mohammad Mahmoodi Meymand
Abstract
Generally, mineral processing plants generate a large quantity of waste in the form of fine particles. The flotation speed of mineral microbubbles by coarse bubbles is dramatically higher than that of individual particles. The advantage of microbubbles is due to the increase of binding efficiency of ...
Read More
Generally, mineral processing plants generate a large quantity of waste in the form of fine particles. The flotation speed of mineral microbubbles by coarse bubbles is dramatically higher than that of individual particles. The advantage of microbubbles is due to the increase of binding efficiency of conventional bubbles with fine particles coated with microbubbles. Here, the focus is on reducing chemicals consumption and improving recovery. After preparing a representative sample, XRF, XRD, and mineralogical analyses were performed. Then 50 experiments were selected by experimental design using the response surface method (RSM), and in the form of central Composite design (CCD) by (design expert) DX 13 software. The interactions of collector consumption, frother agent, pH, particle size, and solid percentage were investigated, and 25 experiments using typical flotation and without nano-microbubbles and others with nano-microbubbles were conducted. The laboratory standard limit of the collector used in the pilot plant of the Sarcheshmeh Copper copper complex is 40 g/t (25 g/t of C7240 plus 15 g/t of Z11). Here, by consuming 20 g/t of collector in the absence of nanomicrobubbles, a recovery of 79.96% and in the presence of nanomicrobubbles, a recovery of 80.07% was obtained, that is a 50% reduction in collector consumption and a 0.11% increase in recovery was observed. Also the laboratory standard limit of frother used in the pilot plant of Sarcheshemeh Copper Complex is 30 g/t (15 g/t of MIBC plus 15 g/t of A65). Here, by using 10 g/t of frother in the absence of nanomicrobubbles, a recovery of 78.12%, and in the presence of nanomicrobubbles, a recovery of 82.05% was obtained. In other words, a decrease of 66.6% in the consumption of frother and an increase of 1.93% in recovery was observed.
M. Shamsi; M. Noparast; Seyyed Z. Shafaie; M. Gharabaghi; S. Aslani
Abstract
Copper smelting slags are hard materials. Therefore,to recover their copper by flotation method, grinding should be carried out to obtain optimal particle size. Copper smelting slags in the Bardeskan district, with work index of 16.24 kwh/st, were grinded for 65 minutes to reach an acceptable degree ...
Read More
Copper smelting slags are hard materials. Therefore,to recover their copper by flotation method, grinding should be carried out to obtain optimal particle size. Copper smelting slags in the Bardeskan district, with work index of 16.24 kwh/st, were grinded for 65 minutes to reach an acceptable degree of freedom for the flotation tests, with particle size of 80%, smaller than 70 μm. With this grinding time, degree of freedom for copper-bearing minerals was achieved 85-90%. The floatation method performed and the procedure used for the optimization of the effective parameters were described in this paper. The results obtained for the flotation tests, carried out at the optimal conditions after grinding the slags (with a grinding time of65 minutes), showed 62.23% of copper recovery, while, by flotation of copper slags at optimal conditions after increasing the grinding time to 85 minutes (d80 = 48µ), the Cu recovery was increased to 79.89%.