Exploitation
Behnam Alipenhani; mehran jalilian; Abbas Majdi; Hassan Bakhshandeh Amnieh; Mohammad Hossein Khosravi
Abstract
The paper presents the effect of the dip of joints, joint spacing, and the undercutting method on the height of the caving in block caving. The obtained results show that among the three investigated parameters, respectively, the dip of joints, undercutting method, and joint spacing have the greatest ...
Read More
The paper presents the effect of the dip of joints, joint spacing, and the undercutting method on the height of the caving in block caving. The obtained results show that among the three investigated parameters, respectively, the dip of joints, undercutting method, and joint spacing have the greatest effect on increasing the height of the caving zone. Comparing the data obtained from physical and numerical modeling shows a 97% match. Also, by increasing the joint spacing from 4 to 6 cm, 14%, from 6 to 8 cm, about 35%, and from 8 to 10, about 50%, the height of the caving zone has decreased. Regarding the dip of the joint, with the dip increasing from 30 to 45 degrees, about 3% of the caving height decreases. By increasing the dip of the joint from 45 to 60 degrees, the caving height has decreased by 42%. By increasing this value from 60 to 75 degrees, the caving height has increased by 50%. Also, changing the undercutting method from symmetric to advanced undercutting has increased the caving height by 40%. Additionally, three mathematical models have been proposed based on the shape of the caving zone in physical modeling.
B. Alipenhani; A. Majdi; H. Bakhshandeh Amnieh
Abstract
The present work aims at implementing Response Surface Methodology (RSM) in order to generate a statistical model for Minimum Required Caving Span (MRCS) and estimate both the individual and mutual effects of the rock mass parameters on rock mass cavability. The adequate required data is obtained from ...
Read More
The present work aims at implementing Response Surface Methodology (RSM) in order to generate a statistical model for Minimum Required Caving Span (MRCS) and estimate both the individual and mutual effects of the rock mass parameters on rock mass cavability. The adequate required data is obtained from the result of numerical modeling. In this work, various arrays of numerical simulations (480 models) are carried out using the UDEC software in order to study the rock mass cavability thoroughly. The effect of each individual parameter and their mutual effect on MRCS are investigated by means of ANOVA. ANOVA indicates that all the chosen parameters (depth, dip of the joint, number of joints, angle of friction of the joint surface, and joint spacing) highly affect MRCS. In other words, the results of ANOVA are in high agreement with the results of the conventional sensitivity analysis. Moreover, a combination of joint spacing and joint inclination has the highest mutual effect on MRCS, and a combination of undercut depth and joint spacing has the lowest effect on MRCS.
B. Alipenhani; A. Majdi; H. Bakhshandeh Amnieh
Abstract
Determining the hydraulic radius of the undercut in the block caving method is one of the key issues in this method. The hydraulic radius is directly related to the minimum caving span. In this research work, the rock mass cavability is investigated using the UDEC and 3DEC software. Since the factors ...
Read More
Determining the hydraulic radius of the undercut in the block caving method is one of the key issues in this method. The hydraulic radius is directly related to the minimum caving span. In this research work, the rock mass cavability is investigated using the UDEC and 3DEC software. Since the factors affecting the cavability are very diverse and numerous, firstly, by 2D modeling in the UDEC software and examining the trend of changes in the minimum caving span, the most important factors including the depth, dip of the joint, number of joints, angle of friction of the joint surface, and joints spacing are selected for the final study. The variation trend of each variable is investigated by keeping the other variables constant (single-factor study) among various factors. In the second step, the minimum caving span for the five main factors and values is determined in the single-factor study using the SPSS software and the multivariate regression method. Then the power function of the minimum caving span is chosen based on the selected variables with a coefficient of determination of 0.76. In continuation, a simple 3D model is built from the undercut. A linear equation is achieved between the results of the 3D and 2D modeling results in similar conditions. In a model with certain conditions, using the equation obtained from the numerical method, the calculated hydraulic radius of caving is 22.5 m, which is close to the result obtained from the Laubscher's empirical method with the same condition (24 m).
J. Zadhesh; A. Majdi
Abstract
The mechanisms of deformation and failure of the structures in and on the jointed rock masses are often governed by the characteristics of the geometrical properties of joints. Since the joint geometry properties have a range of values, it is helpful to understand the distribution of these values in ...
Read More
The mechanisms of deformation and failure of the structures in and on the jointed rock masses are often governed by the characteristics of the geometrical properties of joints. Since the joint geometry properties have a range of values, it is helpful to understand the distribution of these values in order to predict how the extreme values may be compared with the values obtained from a small sample. This work studies three datasets of joint systems (1652 joint data) from nine outcrops of igneous, sedimentary, and metamorphic rocks in order to determine the probability distribution function of the rock joint geometry properties. Consequently, the goodness-of-fit (GOF) tests are applied to obtain the data. According to these GOF tests, the Lognormal is the best probability distribution function representing the joint spacing, aperture, and trace length. The Cauchy is the best probability distribution function for the joint dip angle. It is found that the Cauchy distribution function is the best probability distribution function to represent the joint dip direction of igneous rocks, and the Burr distribution function is the best probability distribution function to define the joint dip direction of the sedimentary and metamorphic rocks.
M. M. Nazempour; A. Majdi
Abstract
Prediction of the length of grout penetration and assessment of the groutability around the boreholes in the jointed rocks have a crucial effect on the planning and execution of grouting. Grout distribution in jointed rocks is a function of the geo-mechanical properties of rock mass, grout properties, ...
Read More
Prediction of the length of grout penetration and assessment of the groutability around the boreholes in the jointed rocks have a crucial effect on the planning and execution of grouting. Grout distribution in jointed rocks is a function of the geo-mechanical properties of rock mass, grout properties, and grout operational performance. This paper describes an analytical model based on the Newton’s second law, with the assumption of disk-shape model for the joints in order to calculate the maximum length of grout penetration in the horizontal and angled joints. It is shown that the proposed formulas can predict the length of grout penetration in rock masses with numerous joint sets as well. In order to validate the proposed model, it is compared with the existing analytical and empirical criteria, showing a very good accordance with their calculated results. Finally, the proposed analytical model is used to design the grout planning of a water conveying tunnel that is subjected to a heavy inflow. The design results in a successful filling of the vacant space behind the segmental lining and sealing the tunnel to stop the inrush water. These show that the model proposed in this paper can be successfully applied in practice.
A. Majdi; M. Yazdani
Abstract
The hydraulic jacking refers to the process of crack growth of the pre-existing joints in the rock mass under grout pressure above the minimum in-situ stress. Thus it is essential to understand the resistance behavior of the joints and maximum grout pressure. This paper describes a novel method for determining ...
Read More
The hydraulic jacking refers to the process of crack growth of the pre-existing joints in the rock mass under grout pressure above the minimum in-situ stress. Thus it is essential to understand the resistance behavior of the joints and maximum grout pressure. This paper describes a novel method for determining the hydraulic jacking occurrence in anisotropic rock mass based on the principle of fracture mechanics. This method is established on three stage developments: developing an equation in order to calculate the equivalent stress intensity factor at the joint tip, determining the fracture toughness by employing the Brazilian disc test with a loading rate of 0.1 MPa/s on the rock cored samples, and assessing the stability of joints using the maximum tangential stress criterion. By comparing the joint stress intensity factor and fracture toughness in the direction of rock anisotropy, the joint stability is evaluated. Then the maximum allowable grout pressure is analytically formulated as a function of fracture toughness in order to avoid the unwanted deformations in the joints (i.e. jacking) during grouting. In order to validate the proposed method, the data obtained from the boreholes used to construct water curtain at the Sanandaj Azad Dam in phyllite rocks are analyzed. Finally, it is concluded that the growth and expansion of the joints due to the instability under grout pressure leads to an increased cement take and the occurrence of hydraulic jacking. In addition, the proposed equation for computing maximum allowable grout pressure provides an acceptable agreement with the existing empirical rules and the results of the field data.
V. Maazallahi; A. Majdi
Abstract
The uniaxial compressive strength (UCS) of intact rocks is one of the key parameters in the course of site characterizations. The isotropy/anisotropy condition of the UCS of intact rocks is dependent on the internal structure of the rocks. The rocks with a random grain structure exhibit an isotropic ...
Read More
The uniaxial compressive strength (UCS) of intact rocks is one of the key parameters in the course of site characterizations. The isotropy/anisotropy condition of the UCS of intact rocks is dependent on the internal structure of the rocks. The rocks with a random grain structure exhibit an isotropic behavior. However, the rocks with a linear/planar grain structure generally behave transversely-isotropic. In the latter case, the UCS of intact rocks must be determined by a set of laboratory tests on the oriented rock samples. There are some empirical relations available to describe the strength of these rocks. Though characterization of transversely-isotropic rocks is practically a 3D problem, but these relations provide only a 2D description. In this paper, a method is proposed to provide a 3D description of UCS of transversely-isotropic rocks. By means of this formulation, one can determine UCS along with any arbitrary spatial direction. Also, a representative illustration of UCS is proposed in the form of contour-plots on a lower hemisphere Stereonet. The method is applied to an actual case study from the Kanigoizhan dam site located in the Kurdistan Province (Iran). Application of the proposed method to the phyllite rocks of this site show that the direction perpendicular to the dam axis exhibits the most anisotropic behavior. Hence, it is essential to take the strength anisotropy into account during the relevant analysis. The results obtained, together with the statistical variation of UCS, provide a practical approach to select the proper values of UCS according to the scope of the analysis.
Rock Mechanics
S. Ali Madadi; A. Majdi; M. H. Khosravi; A.R. Kargar
Abstract
Fracture mechanics is a vital component involved in studying the exact behavior of rock materials. Detection and assessment of the behavior of rock joints injected by grout plays an important role in numerical modelling in rock mechanic projects. The importance of mechanisms associated with initiation ...
Read More
Fracture mechanics is a vital component involved in studying the exact behavior of rock materials. Detection and assessment of the behavior of rock joints injected by grout plays an important role in numerical modelling in rock mechanic projects. The importance of mechanisms associated with initiation and propagation of cracks due to hydraulic fracturing has led to a considerable interest in investigation and analysis of this phenomenon. In this work, the process of propagation of cracks on the wall of boreholes, drilled in single and bi-material structures, was simulated in ABAQUS software employing the extended finite element method. The energy method was implemented to obtain the stress intensity factor and energy release rate through applying J integral around the crack tip. The method was applied to two rock types, diorite and granite at the Chadormalu iron mine located in the central part of Iran. It was concluded that assuming the same geometry, the possibility of crack propagation at the boundary between two materials was more than the single material medium. Therefore, in dealing with a bi-material medium, if the purpose is to measure the in situ stresses, the measurement should not be performed on the boundary between the two materials.
