Mineral Processing
Mohammadreza Shahbazi; Hadi Abdollahi; Sied Ziaeddin Shafaei; Ziaeddin Pourkarimi; Sajjad Jannesar Malakooti; Ehsan Ebrahimi
Abstract
Tabas coal possesses favorable plastometric properties that make it suitable for use in metallurgical industries as coking coal. However, its high sulfur content, which stands at approximately 2%, poses a significant environmental pollution risk. Additionally, reducing ash content to below 10% is a critical ...
Read More
Tabas coal possesses favorable plastometric properties that make it suitable for use in metallurgical industries as coking coal. However, its high sulfur content, which stands at approximately 2%, poses a significant environmental pollution risk. Additionally, reducing ash content to below 10% is a critical objective of this study to prevent a decline in coal's thermal efficiency in the metallurgical industries. This research work investigates the removal of sulfur and ash from Tabas coal samples using the biological methods including bioflotation and bioleaching. Initially, a combination of mesophilic bacteria including Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans, and Leptosprillium ferrooxidans were employed in the bioflotation method to detain pyrite sulfur in the Tabas coal samples. The highest reduction percentages of pyrite sulfur and ash were equal to 62% and 54.18%, respectively. In the next stage, bioleaching experiments were conducted, the effect of the test time, percentage of bacteria by volume, percentage of coal solids, and absence of bacteria on the amount of sulfur and ash removal was investigated. The test time emerged as the most critical factor. The best sulfur removal was achieved using bioleaching, with a maximum removal of 72.43%, observed for the PE coal sample. Bioflotation also achieved significant sulfur removal, with a maximum removal of 61% observed for the same sample. On the other hand, the best ash removal was achieved using bioflotation, with a maximum removal of 68.98% observed for the PE coal sample, and a maximum removal of 69.34% observed for the B4B2 coal sample using bioleaching. Finally, this research work conducted a comparison of biological methods to determine the amount of sulfur and ash reduction achieved. The results showed that both bioleaching and bioflotation were effective for coal desulfurization and ash removal, with bioleaching performing slightly better for sulfur removal and bioflotation performing slightly better for ash removal.
Sajjad Jannesar Malakooti; Hadi Abdollahi; Ziaeddin Pourkarimi; Behrouz Karimi Shahraki; Mehdi Rahimi; Mohammadreza Shahbazi; Ahmad Rahmanian kooshkaki
Abstract
Parvadeh IV and East Parvadeh mines are two main coal-producing zones within the Tabas coalfield, east of Iran. Since studies have shown that C1 and B2 are the most important working seams in the Parvadeh IV and east Parvadeh areas, this research work focuses on these two coal seams. Syngenetic pyrite ...
Read More
Parvadeh IV and East Parvadeh mines are two main coal-producing zones within the Tabas coalfield, east of Iran. Since studies have shown that C1 and B2 are the most important working seams in the Parvadeh IV and east Parvadeh areas, this research work focuses on these two coal seams. Syngenetic pyrite is available as framboids related to macerals. Decreasing the sulfur content is especially hard when the pyrite particles are fine-grained, finely disseminated, and intergrown with the coal maceral structure. The sulfur content measured in C1 and B2 seams varies from 0.98% to 5.57% and from 0.73% to 5.25%, respectively, with an average of 2.39% and 2.5%. We use a method to predict how coal desulfurized the C1and B2seams of Parvadeh IV and C1 seams of east Parvadeh mines in the Tabas coalfield. The results have given new proofs for the presence of pyrite and clay minerals within the coalfield zone, and to identify a method to predict coal desulfurization with conventional processing and cost-effective methods. The coal preparation strategy in MEMRADCO, Parvadeh, and Ehyasepahan coal-cleaning plants not as it expels mineral matter and pyrite but too reduces the content of most inorganic components.
M. Hosseini Nasab; M. Noaparast; H. Abdollahi
Abstract
In this research work, the bio-leaching of Co and Ni from an iron-rich laterite ore is assessed using the acidophilic heterotrophic (Delftia acidovorans)and autotrophic (Acidithiobacillus ferrooxidans) bacteria. The metabolic products of the acidophilic bacteria play an important role in bio-leaching. ...
Read More
In this research work, the bio-leaching of Co and Ni from an iron-rich laterite ore is assessed using the acidophilic heterotrophic (Delftia acidovorans)and autotrophic (Acidithiobacillus ferrooxidans) bacteria. The metabolic products of the acidophilic bacteria play an important role in bio-leaching. The results obtained from the indirect bio-leaching indicate the highest nickel recoveries of up to 83.65% and 80.18%, respectively, by the supernatants of Acidithiobacillus ferrooxidans and Delftia acidovorans, both measured at 90 °C for 3 h with a stirring speed of 370 rpm and S/L of 0.1, while the corresponding cobalt recovery rates have reached 86.93% and 83.94%, respectively. The iron dissolution rates in these conditions for the two studied bacteria are 64.34% and 54.41%, respectively. The nickel and cobalt extractions by the indirect bio-leaching of Delftia acidovorans are, respectively, 29.84% and 23.75% higher than those for the direct bio-leaching, performed at 30 °C and 150 rpm of an incubator shaker for 30 days. For the indirect bio-leaching, the chemical control has a larger influence on the dissolution rate of the iron-rich laterite compared to the diffusion control. The activation energies of nickel and cobalt in the chemical control model are 40.07 and 39.08 kJ/mol, respectively.
H. A. Mirzaei; M. Noaparast; H. Abdollahi
Abstract
The precipitation of aluminum hydroxide from a supersaturated sodium aluminate solution is known as an essential production step in the Bayer process. In this work, the real precipitation process in the Iran Alumina Plant was modeled by the historical data with the help of Design Expert. According to ...
Read More
The precipitation of aluminum hydroxide from a supersaturated sodium aluminate solution is known as an essential production step in the Bayer process. In this work, the real precipitation process in the Iran Alumina Plant was modeled by the historical data with the help of Design Expert. According to the results obtained, the recovery is significantly improved with decrease in the super-saturation factor (α) of the solution. However, this modification was found to be the most difficult change due to the operational problems. The results obtained indicated the significant impact of the seed size on the product size. The negligible effects of the other parameters involved on controlling the amount of fine grains (< 44 µm) and coarse grains (> 150 µm) in the product showed the significance of reactivating the classification and agglomeration sections. Ultimately, it was found that the recovery process could be enhanced from 46.32% to 47.86% at a constant α by increasing the seed concentration to 400 g/L, increasing the retention time by adding two precipitation tanks and reducing the temperature of the last precipitation tank by 2 ºC (by reducing the temperature of the inlet suspension), while preserving the quality of the product.
M. Hosseini Nasab; M. Noaparast; H. Abdollahi
Abstract
Due to the decreasing production of nickel and cobalt from sulfide sources, the Ni and Co extraction from the oxide ores (laterites) have become more prevalent. In this research work, the effects of calcination prior to leaching, acid concentration, percent solid, pH, and stirring speed on the nickel ...
Read More
Due to the decreasing production of nickel and cobalt from sulfide sources, the Ni and Co extraction from the oxide ores (laterites) have become more prevalent. In this research work, the effects of calcination prior to leaching, acid concentration, percent solid, pH, and stirring speed on the nickel and cobalt recoveries from an iron-rich laterite ore sample were investigated using different organic acids. Then the response surface methodology was implemented in order to optimize the various parameters. By the design of experiments, the compound optimal concentrations of the three different organic acids (gluconic acid: lactic acid: citric acid with a ratio of 1:2:3) were 3.18 M, and S/L = 0.1, pH = 0.5, and the stirring speed = 386 rpm. With the aid of kinetic studies, a temperature of 75 °C, and a test time of 120 minutes, the highest nickel and cobalt recoveries were 25.5% and 37.6%, respectively. In the optimal conditions, the contribution of the percent solids to the nickel recovery was the most and negative, after which the contribution of pH was negative, and finally, the acid concentration had a positive effect. In the optimal conditions, the acid concentration, pH, and solid content were, respectively, important in the cobalt recovery. The SEM results showed that the surface of feed and residue particles in the optimal conditions was not significantly different, and the laboratory data was fitted to a shrinking core model. The results obtained indicated that the reaction rate was controlled by the diffusion reaction at the particle surface, and the activation energies of 11.09 kJ/mol for nickel and 28.04 kJ/mol for cobalt were consistent with this conclusion
Mineral Processing
A.H. Rezaei; H. Abdollahi; M. Gharabaghi; A. A. Mohammadzadeh
Abstract
In the recent decades, water scarcity has become a major challenge for many reasons, especially the inadequate use of water resources. The mineral processing plant is among the most important water-consuming industries. Filtration, as one of the important processes in water recovery, is a process in ...
Read More
In the recent decades, water scarcity has become a major challenge for many reasons, especially the inadequate use of water resources. The mineral processing plant is among the most important water-consuming industries. Filtration, as one of the important processes in water recovery, is a process in which the solid-suspended particles are removed from the liquid. In the present work, the effect of the additives affecting the filtration process upon the responses including the resistance to filter cloth (R), specific cake resistance (α), moisture content, water recovery rate, and cake formation rate by the vacuum top-feed method is investigated. The experiments are performed by two methodologies: one-factor-at-a-time and statistical analysis. The additives are the flocculant, coagulant, surfactant, and filter aid. According to the one-factor-at-a-time methodology, the optimal type and dosage of the variables are as follow: flocculant A25 with a concentration of 15 g/L, perlite as the filter aid with an amount of 2.5%, surfactant cop 20-101 with a concentration of 3 cc/L, and the coagulant CaCl2.2H2O with a concentration of 2.5 g/L. The usage of the flocculant, surfactant, and filter aid at the same time is also statistically analyzed with the aim of maximizing the cake formation rate and minimizing the moisture content of the filter cake. Under the optimal conditions and taking into account 11.68 g/t of the flocculant A25, 3.8% of perlite as the filter aid, and2.92 cc/L of the surfactant cop 20-101, the cake formation rate and the moisture content were obtained to be 0.297 mm/s and 12.7 %, respectively.
Mineral Processing
H. Jafari; H. Abdollahi; M. Gharabaghi; A.A. Balesini
Abstract
In this research work, solvent extraction and stripping of zinc ions from a Zn-Mn-Cd-bearing solution was investigated using D2EHPA as the extractant in a chloride medium. The efficiency of the extraction and stripping stages was evaluated separately, and different parameters such as the pH, extractant ...
Read More
In this research work, solvent extraction and stripping of zinc ions from a Zn-Mn-Cd-bearing solution was investigated using D2EHPA as the extractant in a chloride medium. The efficiency of the extraction and stripping stages was evaluated separately, and different parameters such as the pH, extractant concentration, reaction temperature, and contact time were studied. Based on the results obtained, 97% of zinc, 14% of manganese, and 3% of cadmium were extracted at pH = 2.5, 10% (v/v) of D2EHPA, and 40 °C from the solution containing 5 g L-1 of each metal ion. The stripping isotherms of zinc, manganese, and cadmium at different pH values showed that manganese and zinc were stripped at two different pH values. Thus more than 70% of manganese and more than 90% of zinc were stripped at pH = 2.5 and pH = 0.5, respectively. Kinetic studies indicated that the extraction and stripping of zinc in the first 0.5-1 minute was high. The McCabe–Thiele diagrams showed that two stages of extraction and two stages of stripping in the continuous counter-current flow condition were adequate to separate zinc from Mn and Cd. The dominant Zn species extracted by D2EHPA was ZnCl+, and the values for the thermodynamic parameters ΔHo, ΔSo, and ΔGo were 25.65 kJ mol−1, 79.20 J K−1 mol−1, and 0.86 kJ mol−1, respectively, which showed that the reaction was endothermic at equilibrium.
Mineral Processing
V. Radmehr; Seyed Z. Shafaei; M. Noaparast; H. Abdollahi
Abstract
This paper presents a new approach for flotation circuit design. Initially, it was proven numerically and analytically that in order to achieve the highest recovery in different circuit configurations, the best equipment must be placed at the beginning stage of the flotation circuits. The size of the ...
Read More
This paper presents a new approach for flotation circuit design. Initially, it was proven numerically and analytically that in order to achieve the highest recovery in different circuit configurations, the best equipment must be placed at the beginning stage of the flotation circuits. The size of the entering particles and the types of streams including pulp and froth were considered as the basis for specialization of the flotation processes. In the new approach, the flotation process plays as the two functions of primary and secondary concentrations. The proposed approach was applied to a lead flotation circuit of a lead-zinc flotation plant. The results obtained showed that in most traditional-oriented circuits, a large part of the streams containing valuable metals were returned to the rougher stage, which, in turn, reduced the efficiency and caused perturbation. In the new approach, providing more control over unit operations in the circuit could provide a higher performance. In addition, in cases where zinc minerals are liberated from their gangue in coarse size, the new approach, by generating coarse-grained tailing, can prevent excessive grinding of zinc minerals in the feed into the zinc flotation circuit.
Mineral Processing
M. Salehfard; M. Noaparast; Seyed Z. Shafaei; H. Abdollahi
Abstract
A lead-zinc carbonate ore sample containing 2.5% Pb and 9.39% Zn was used in this research work. The sample was prepared from the Darreh-Zanjir mine located in the Yazd province (Iran). Influences of the influential factors on flotation of smithsonite and cerussite were investigated. Among the different ...
Read More
A lead-zinc carbonate ore sample containing 2.5% Pb and 9.39% Zn was used in this research work. The sample was prepared from the Darreh-Zanjir mine located in the Yazd province (Iran). Influences of the influential factors on flotation of smithsonite and cerussite were investigated. Among the different parameters involved, dosages of the dispersant, depressants, sulfidizing agent, and collectors de-sliming prior to lead or zinc flotation were essential for the effective recovery and grade of the Zn and Pb flotation concentrates. In addition, the anionic, cationic, and mixed (cationic/anionic) collectors were employed for flotation of smithsonite. The results of reverse and cumulative flotation of both Zn and Pb were relatively low in comparison with the direct process without depressant. Flotation of smithsonite using mixed collectors (Armac C+KAX) showed promising results. Also dosages of chemicals in the cleaning stage for the Zn and Pb concentrates were optimized, and finally, after the cleaner stage for both lead and zinc, a cerussite concentrate with Pb grade and recovery of 49.82% and 60.06%, respectively, and smithsonite concentrate with Zn grade and recovery of 35.47% and 68.56%, respectively, were obtained under the optimal conditions. Furthermore, kinetics of Zn and Pb oxide mineral flotations in the rougher and cleaner stages were studied, which showed that some kinetics models, especially the classical first-order model, could predict the flotation behaviour of the Zn and Pb oxide minerals.
