M. Bahaaddini; M. Serati; M. H. Khosravi; B. Hebblewhite
Abstract
A proper understanding of the shear behaviour of rock joints and discontinuities is yet a remaining challenge in the rock engineering research works owing to the difficulties in quantitatively describing the joint surface roughness both at the field and the laboratory scales. Several instruments and ...
Read More
A proper understanding of the shear behaviour of rock joints and discontinuities is yet a remaining challenge in the rock engineering research works owing to the difficulties in quantitatively describing the joint surface roughness both at the field and the laboratory scales. Several instruments and techniques have been developed over the years for the surface characterisation of joints at the field- and laboratory-scale investigations, amongst which the application of the photogrammetry methods has obtained a growing popularity. This work evaluates the applicability of the photogrammetry techniques for the characterisation of joint surface topography and texture at micro-scales, which has been largely understudied in the literature. Three tensile joint surfaces are digitized using photogrammetry, and the results are compared with those obtained from laser scans with a high 3D accuracy. A comprehensive statistical analysis is then undertaken on the digitized point clouds in order to assess the performance of photogrammetry in surface characterisation. The results of this work show that the height differences between the resulting point clouds from the two adopted techniques (photogrammetry and 3D laser scanning) follow the normal distribution with the mean values close to zero. The statistical analyses illustrate that the measured joint surfaces using the photogrammetry techniques are in good agreement with the laser scanning data, confirming that photogrammetry is a capable method for characterising the joint surface roughness even at micro-scales. Interestingly, the results obtained further indicate that the accuracy and preciseness of the photogrammetry techniques are independent from the joint roughness coefficient but the camera and configuration parameters remarkably control the performance of the measurement.
Rock Mechanics
Anant Saini; Jitendra Singh Yadav
Abstract
The goal of this research work was to use an Artificial Neural Network (ANN) model to predict the ultimate bearing capacity of circular footing resting on recycled construction waste over loose sand. A series of plate load tests were conducted by varying the thickness of two sizes of recycled construction ...
Read More
The goal of this research work was to use an Artificial Neural Network (ANN) model to predict the ultimate bearing capacity of circular footing resting on recycled construction waste over loose sand. A series of plate load tests were conducted by varying the thickness of two sizes of recycled construction waste (5 mm and 10.6 mm) layer (0.4d, 0.6d, 0.8d, 1d, and 1.2d, d: diameter of footing) prepared at different relative densities (30%, 50%, and 70%) overlaying. The ultimate bearing capacity obtained for various combinations was used to develop the ANN model. The input parameters of the ANN model were thickness of recycled construction waste layer to diameter of circular footing ratio, angle of internal friction of sand, unit weight of sand, angle of internal friction of recycled construction waste and unit weight of recycled construction waste, and the model's output parameter was ultimate bearing capacity. The FANN-SIGMOD_SYMMETRIC model with topology 3-2-1 provided a higher estimate of the ultimate bearing capacity of circular footing, according to the ANN findings. The sensitivity analysis also revealed that the unit weight of sand and angle of internal friction of sand had insignificant effects on ultimate bearing capacity. The estimated ultimate bearing capacity was most affected by the angle of internal friction of recycled construction waste. The result of multiple linear regression analysis was not as good as the ANN model at predicting the ultimate bearing capacity.
A Chamani; Vamegh Rasouli
Abstract
The rapid growth in natural gas consumption has increased the need for gas storage, in particular in the form of injection into depleted reservoirs. Also, CO2 sequestration into the depleted reservoirs has attracted a large attention recently. However, it is important to ensure that the injection pressure ...
Read More
The rapid growth in natural gas consumption has increased the need for gas storage, in particular in the form of injection into depleted reservoirs. Also, CO2 sequestration into the depleted reservoirs has attracted a large attention recently. However, it is important to ensure that the injection pressure is maintained below a certain limit to avoid unsealing the cap rock or reactivation of any existing fracture planes within or above the reservoir rocks. In particular, it can be thought that gas injection into formations with non-horizontal structures, such as anticlines, is more problematic than horizontal formations due to the development of shear zones in such geometries. This could potentially result in long term wellbore problems such as casing collapse or shearing along a fault or fracture plane intersecting the wellbore. In this study we compare the stress profile changes before and after gas injection into three structures: a horizontal and two anticline formations with different slopes at their flanks. For this purposes a 3D numerical simulator was used. The program was developed using finite element method (FEM) and the code was written in Fortran.The stress magnitudes along curved profiles were compared for three structures at a similar depth. A limited extension of a porous zone was assumed in this study. The results indicate how as structure becomes more curvy in its geometry the likelihood of shear displacement increases.
Bahman Ghobadi; Mohammad Noaparast; Seid Ziaedin Shafaei; Majid Unesi
Abstract
This study investigates the optimization of gold dissolution from Aghdarre ore. Therefore, a laboratory investigation was initiated, to improve the leaching conditions with the objective of maximizing mill capacity with no reduction on gold recovery. It was observed that the time reduction from 25 to ...
Read More
This study investigates the optimization of gold dissolution from Aghdarre ore. Therefore, a laboratory investigation was initiated, to improve the leaching conditions with the objective of maximizing mill capacity with no reduction on gold recovery. It was observed that the time reduction from 25 to 15 hours did not change the gold recovery. In the other words, it indicated that a capacity of 140t/h can be sustained without detrimental effect on gold recovery. The optimum parameters were 700g/t NaCN, 46% solid in pulp, pH=10, and d80=45 microns using the Taguchi method. So, the gold recovery was obtained 90.71%. Also, it was concluded that the NaCN concentration was the most effective parameter and the solid percent plus retention time had the lowest effects on this process.
Mohammad Fatehi; Arash Pashapour; Javad Gholamnejad
Abstract
Most of the Earth's crust contains fluids, and fractures are common throughout the upper part. They exist at a wide range of scales from micro-fractures within grains to major faults and shear zones that traverse the crust. In this paper, the stress-dependent permeability in fractured rock masses have ...
Read More
Most of the Earth's crust contains fluids, and fractures are common throughout the upper part. They exist at a wide range of scales from micro-fractures within grains to major faults and shear zones that traverse the crust. In this paper, the stress-dependent permeability in fractured rock masses have been investigated considering the effects of nonlinear normal deformation and shear dilation of fractures using a two-dimensional distinct element method program, UDE. A new analytical and numerical model was proposed to determine the relationship between fracture dip angle, aperture and permeability. The numerical work were conducted in two ways: (1) increasing the overall stresses with a fixed ratio of horizontal to vertical stresses components; and (2) increasing the differential stresses (i.e., the difference between the horizontal and vertical stresses) while keeping the magnitude of vertical stress constant. The results showed that at the stress ratio of 1 the significant shear dilation occurs at an approximately low stress and mean fracture angles. For the differential stresses case, the shearing process can result in breakage of the asperities, resulting in the decrease of the dilation rate and strain softening of the fracture.
M. Hosseinzadeh; M. Alizadeh; S. M. Raouf Hosseini
Abstract
In this work, a bench-scale process was developed using mineral-processing methods to recover iron from a placer deposit located in Bardaskan, Khorasan-e-Razavi, Iran. The mineralogical studies were performed by X-ray Diffraction (XRD), X-ray Fluorescence (XRF), Electron Probe Micro-Analyzer (EPMA), ...
Read More
In this work, a bench-scale process was developed using mineral-processing methods to recover iron from a placer deposit located in Bardaskan, Khorasan-e-Razavi, Iran. The mineralogical studies were performed by X-ray Diffraction (XRD), X-ray Fluorescence (XRF), Electron Probe Micro-Analyzer (EPMA), and an optical microscope. These studies indicated that titanomagnetite, magnetite, and hematite were presented in the sample as valuable minerals. In contrast, the gangue minerals were silicates such as pyroxene, plagioclase, quartz, feldspar, calcite, and some secondary minerals. The optimum liberation degree of the iron-containing minerals was obtained to be 75 µm with average Fe and TiO2 contents of 5% and 1%, respectively. The analysis showed that magnetite was the main iron mineral, and most of the hematite was formed due to martitization. Also minor ilmenite contents were found in hematite and magnetite in a blade form. The maximum TiO2 content in the magnetite lattice was 19%, only 8% of which was recovered to the magnetic product. Eventually, an iron concentration flow sheet was developed, which included the removal of a major part of silicates and then iron minerals by a low intensity wet magnetic separator. The final product contained 55, 7.8, and 0.77% of Fe, TiO2, and V2O5, respectively, which can be used for iron production, and V2O5 extraction (as the by-product).
Mine Economic and Management
H. Dehghani
Abstract
Forecasting the prices of metals is important in many aspects of economics. Metal prices are also vital variables in financial models for revenue evaluation, which forms the basis of an effective payment regime using resource policymakers. According to the severe changes of the metal prices in the recent ...
Read More
Forecasting the prices of metals is important in many aspects of economics. Metal prices are also vital variables in financial models for revenue evaluation, which forms the basis of an effective payment regime using resource policymakers. According to the severe changes of the metal prices in the recent years, the classic estimation methods cannot correctly estimate the volatility. In order to solve this problem, it is necessary to use the artificial algorithms, which have a good ability to predict the volatility of various phenomena. In the present work, the gene expression programming (GEP) method was used to predict the copper price volatility. In order to understand the ability of this method, the results obtained were compared with the other classical prediction methods. The results indicated that the GEP method was much better than the time series and multivariate regression methods in terms of the prediction accuracy.
Mineral Processing
M. Maleki Moghaddam; E. Arghavani; A.R. Ghasemi; S. Banisi
Abstract
Liner design has become an increasingly more important tool for the AG/SAG mill performance optimization. The Sarcheshmeh copper complex concentration plant uses a SAG mill lined with 48 rows of Hi-Low type liners. Because of breakage of Low type liners and cold welding, the liner replacement task of ...
Read More
Liner design has become an increasingly more important tool for the AG/SAG mill performance optimization. The Sarcheshmeh copper complex concentration plant uses a SAG mill lined with 48 rows of Hi-Low type liners. Because of breakage of Low type liners and cold welding, the liner replacement task of Low with new Hi type liners has become very difficult and time-consuming. With the objective of finding a new design for liners, numerical (3D DEM; discrete element method) simulation and physical modelling in a laboratory mill were used. It was found that changing the liner type from Hi-Low to Hi-Hi could provide an appropriate charge trajectory. The new Hi-Hi type shell liners were designed, manufactured, and installed. With the new liners, the number of broken liners over liner life reduced from 6 to 0 piece, the total changing time for one liner decreased from 21 to 16 minutes, and no cold welding of shell liners was observed. Comparison of the feed rate before and after installation of the new liners for a period of liner life showed an increase from 750 to 850 t/h, which was indicative of a higher flexibility of the mill in encountering ore hardness variations.
N. Hajkazemiha; M. Shariat; M. Monavari; M. Ataei
Abstract
Mining and mineral industry have important role in supporting sustainable development of countries. Many countries rely on the income derived from natural resources, but the exploitation of the natural resources may impact the environment and destroy the ecosystem. Mining activities usually affect the ...
Read More
Mining and mineral industry have important role in supporting sustainable development of countries. Many countries rely on the income derived from natural resources, but the exploitation of the natural resources may impact the environment and destroy the ecosystem. Mining activities usually affect the surrounding lands and ecosystems. The natural, social, and economic environments are part of this ecosystem that are directly involved in these activities. In order to reduce environmentally destructive effects of mining on ecosystem, some important measures must be taken to minimize the negative impacts of mining and related industries. In this paper, for the first time in Iran, a study was conducted to define and categorize the reclamation criteria in three largest iron ore mines. During this research, an attempt was made to establish, define and evaluate forty reclamation criteria. Since the number of criteria is high, to adopt the best practice in mine reclamation program, these criteria should be prioritized. The defined criteria ranked by mining experts, mining managers and related university professors according to their experience and knowledge. The raw collected data were evaluated, processed by Delphi-Fuzzy process and finally analyzed using the Multi-Criteria Decision Making (MCDM) method. The prioritized criteria can provide the authorities with a guideline to start reclamation planning based on the mining and environment requirements and budgeting and also to make the most fruitful, effective and low-cost decisions.
Exploitation
S. Abbaszadeh; Seyed R. Mehrnia; S. Senemari
Abstract
The Ramand region is a part of the magmatic belt in Urmieh-Dokhtar structural zone in Iran, located in the SW of BuinـZahra. This area mainly consists of felsic extrusions such as rhyolites and rhyodacites. Argillic alterations with occurrences of mineralized silica veins are abundant in most of the ...
Read More
The Ramand region is a part of the magmatic belt in Urmieh-Dokhtar structural zone in Iran, located in the SW of BuinـZahra. This area mainly consists of felsic extrusions such as rhyolites and rhyodacites. Argillic alterations with occurrences of mineralized silica veins are abundant in most of the volcanic units. In this research work, we used the GIS facilities for modeling the Ramand geo-spatial databases according to the Fuzzy logic algorithms. The main phase of mineralization occurred in the altered regions and is located near the cross cut fault systems. Therefore, the main criteria for integration were the geological, structural, geophysical, and remotely sensed (Landsat7, ETM+) layers. Also we used a contoured aeromagnetic map for revealing and weighting lineaments. By the Fuzzy techniques applied, all the evidential themes were integrated to prognosis of ore mineralization potentials based on γ = 0.75. As a result, the hydrothermal alterations and their relevant post-magmatic mineralization were introduced in the south and eastern parts of the Ramand region by the fuzzification procedures. Our highlighted recommendation for more exploration activities is focused on the geophysical land surveys (electric and magnetic fields), and the geochemical sampling from mineralized regions in the depth and outcrops of alterations.
Exploitation
M. Lotfi; H. Arefi; A. Bahroudi
Abstract
Hyperspectral remote sensing records reflectance or emittance data in a large sum of contiguous and narrow spectral bands, and thus has many information in detecting and mapping the mineral zones. On the other hand, the geological and geophysical data gives us some other fruitful information about the ...
Read More
Hyperspectral remote sensing records reflectance or emittance data in a large sum of contiguous and narrow spectral bands, and thus has many information in detecting and mapping the mineral zones. On the other hand, the geological and geophysical data gives us some other fruitful information about the physical characteristics of soil and minerals that have been recorded from the surface. The Sarcheshmeh mining area located in the NW-trending Uromieh-Dokhtar magmatic belt within Central Iran is mainly of porphyry type, and is associated with extensive hydrothermal alterations. Due to the semi-arid type of climate with abundant rock exposure, this area is suitable for application of remote sensing techniques. In this work, we focus on generating the alteration maps around Cu porphyry copper deposits using the spectral angle mapper algorithm on Hyperion data by applying two filters named reduction to pole and analytical signal on a total magnetic intensity map and generating the Kd map from radiometry data. What is clear is the high importance of applying the adequate pre-processing on Hyperion data because of low signal-to-noise ratio. By comparing the known deposits in the region with the results obtained by applying the mentioned methods, it is revealed that not all the higher K radiometric values are entirely associated with the hydrothermal alteration zones, and in contrast, the potassic alteration map extracted from Hyperion imagery successfully corresponds to the alteration zones around the Sarcheshmeh mining area. Finally, the results particularly obtained from processing the Hyperion data are confirmed by indices of Cu porphyry deposits in the region.
V. Sarfarazi; K. Asgari; Sh. Mohamadi Bolban Abad
Abstract
The interaction between an internal hole and two surrounded joints under a uniaxial compression are examined using the experimental and discrete element procedures. Inside the concrete sample, two notches and an internal hole are created. The joint angle change from 0° to 90° with an increment ...
Read More
The interaction between an internal hole and two surrounded joints under a uniaxial compression are examined using the experimental and discrete element procedures. Inside the concrete sample, two notches and an internal hole are created. The joint angle change from 0° to 90° with an increment of 30°. The distances between the joint and the internal hole are 2 cm and 3 cm. Also the numerical models are provided. The joint angle change from 0° to 90° with an increment of 15°. The distances between the joint and the internal hole are 2 cm, 3 cm, and 4 cm. The compressive strength is 7.2 MPa. The rate of loading is 0.005 mm/s. The experiment indicates that the failure process is significantly dependent on the notch angle and the joint distance from the hole. The pattern of fracture and mechanism of failure of joints affect the shear strengths of the samples. The models with joint angles of 30° and 60° have a less compressive strength since the pure tensile failure occurs in these configurations. The model strength decreases with decrease in the join spacing. In fact, in the case that the joint spacing is 2 cm, the interaction between the hole and the neighboring joint is so strong. Consequently, the compressive strength is declined. In both approaches of the numerical simulation and experimental methods, the pattern and strength of failure are identical.
Kashitij Guleria; Ravi Kumar Sharma
Abstract
This paper discusses the applications of industrial waste like waste foundry sand (10%, 20%, 30%, and 40%) and calcium carbide residue (3%, 6%, 9%, and 12%) blended with polypropylene fibre (0.25%, 0.50%, 0.75%, and 1%) for soil stabilization. The purpose of this study is to develop a composite of clayey ...
Read More
This paper discusses the applications of industrial waste like waste foundry sand (10%, 20%, 30%, and 40%) and calcium carbide residue (3%, 6%, 9%, and 12%) blended with polypropylene fibre (0.25%, 0.50%, 0.75%, and 1%) for soil stabilization. The purpose of this study is to develop a composite of clayey soil mixed with different additives, so it can be used for improving the geotechnical properties of the clayey soil. Multiple tests are conducted including differential free swell, Atterberg's limits test, compaction tests, unconfined compression test (UCS), and California-bearing ratio test (CBR) on clay soil individually and in different combinations and proportions with additive mixed with each other. The optimum percentage for the additives is found by performing differential free swell index and Atterberg limits test. The results demonstrate that the inclusion of additives in the clayey soil decreases the differential free swell and plasticity index of the composite but raises the composite UCS and CBR values. The maximum increase in the UCS and CBR values is obtained for optimum combination of C:PP:WFS:CC::76.25:0.75:20:3. Based on the CBR values, the thickness of flexible pavement is designed using the IITPAVE software. The results of the software analysis show a reduction in the pavement thickness for various values of commercial vehicles per day (1000, 2000, and 5000) for all combinations. The maximum reduction in layer thickness and construction costs is noticed for C:PP:WFS:CC:76.25:0.75:20:3. To further examine the improvement in the geotechnical properties of soil, calcium carbide residue, and waste foundry sand can be blended with nano-additives for potential uses.
Rock Mechanics
Jitendra Singh Yadav; Poonam Shekhawat; Sreekeshava K S
Abstract
The present work aims to assess the pressure-settlement behaviour of sand beds under a square footing reinforced with coir geotextile using the PLAXIS 3D software. The angle of internal friction of sand was varied from 28° to 38°. The effect of length of coir geotextile (1B, 2B, 3B, 4B, and 5B; ...
Read More
The present work aims to assess the pressure-settlement behaviour of sand beds under a square footing reinforced with coir geotextile using the PLAXIS 3D software. The angle of internal friction of sand was varied from 28° to 38°. The effect of length of coir geotextile (1B, 2B, 3B, 4B, and 5B; B is width of footing) and position of coir geotextile (0.2B, 0.4B, 0.6B, 0.8B, and 1B) to ultimate bearing capacity of sand were examined. A remarkable improvement in ultimate bearing capacity of sand beds was obtained with provision of coir geotextiles. It was observed that the bearing capacity of sand increases by placing coir geotextiles up to a depth of 0.4B from base of footing, thereafter it starts decreasing. The optimum length of coir geotextile was found as 4B-5B. An insignificant improvement in the bearing capacity ratio of sand reinforced with coir geotextile was observed at higher values of angle of internal friction.
F. Moradpouri; A. Moradzadeh; R. Cruz Pestana; M. Soleimani Monfared
Abstract
In this paper, first the limitations of the ray-based method and the one-way wave-field extrapolation migration (WEM) in imaging steeply dipping structures are discussed by some examples. Then a new method of the reverse time migration (RTM), used in imaging such complex structures is presented. The ...
Read More
In this paper, first the limitations of the ray-based method and the one-way wave-field extrapolation migration (WEM) in imaging steeply dipping structures are discussed by some examples. Then a new method of the reverse time migration (RTM), used in imaging such complex structures is presented. The proposed method uses a new wave-field extrapolator called the Leapfrog-Rapid Expansion Method (L-REM) for wave-field extrapolation. This improved method also includes a new imaging condition based on Poynting vector for wave-field separation and calculating the reflection angles. Afterwards, the results obtained for the application of the new RTM method are compared with those obtained by the harmonic-source method as a delay shot or plane wave RTM. Finally, the efficiency of these imaging methods is tested using the BP 2004 2D seismic dataset. The results obtained indicate the superiority of the presented RTM method in imaging such steep dip structures in comparison with the other imaging procedures.
Exploitation
K. Ghanbari; M. Ataei; F. Sereshki; A. Saffari
Abstract
The presence of methane in coal mines is one of the major problems in underground coal mines. Every year, in underground coal mines, a lot of casualties due to outbursts and explosions of methane gas is occurring. Existence of this gas in the mines not only creates a difficult and dangerous situation ...
Read More
The presence of methane in coal mines is one of the major problems in underground coal mines. Every year, in underground coal mines, a lot of casualties due to outbursts and explosions of methane gas is occurring. Existence of this gas in the mines not only creates a difficult and dangerous situation for work but also makes it more expensive. The release of this gas to the air causes a further pollution of the atmosphere and increases the greenhouse gases in the air. Thus Coal Bed Methane (CBM) drainage before, during, and after coal mining is necessary. Accordingly, the CBM drainage can reduce the risks involved in these mines. In the past decade, CBM has offered a significant potential to meet the ever-growing energy demand and can decrease the disastrous events. In this research work, the CBM potential in Eastern Kelariz, Western Razmja, Bornaky, Bozorg, Razzi, and Takht coal mines of Eastern Alborz coal mines company is investigated using the rock engineering systems (RES) based on the intrinsic and geological parameters. Nine main parameters are considered for modeling CBM, and the interactions between these parameters are calculated by a proposed system. Based on the RES method, the parameters that are dominant (depth of cover) or subordinate (gas content) and also the parameters that are interactive are introduced. The proposed approach could be a simple but efficient tool in the evaluation of the parameters affecting CBM, and hence be useful in decision-making. The results obtained show that Razzi coal mine has a good potential to perform CBM drainage.
A. Yusefi; H. R. Ramazi
Abstract
This paper presents an innovative solution for estimating the proximate parameters of coal beds from the well-logs. To implement the solution, the C# programming language was used. The data from four exploratory boreholes was used in a case study to express the method and determine its accuracy. Then ...
Read More
This paper presents an innovative solution for estimating the proximate parameters of coal beds from the well-logs. To implement the solution, the C# programming language was used. The data from four exploratory boreholes was used in a case study to express the method and determine its accuracy. Then two boreholes were selected as the reference, namely the boreholes with available well-logging results and the proximate analysis data. The values of three well-logs were selected to be implemented in a system of equations that was solved, and the effect of each well-log on the estimated values of the proximate parameter was expressed as a coefficient called the effect factor. The coefficients were incorporated in an empirical relationship between the parameter and the three well-logs. To calculate the coefficients used for the most accurate estimation, a total of 22960 systems of equations were defined and solved for every three logs. As there was the possibility of 560 combinations for selecting three logs from all the available 16 logs, the three equation-three variable systems were solved more than 12 million times. The programming methods were utilized to achieve the final results. The results of each system were tested for deviation of the estimated values of volatile matter, ash, and moisture, and the coefficients of the lowest deviation were accepted to be applied in the relation. Implementing this method for estimating the volatile matter resulted in an average deviation of 10.5%. The corresponding estimated values of the ash and moisture contents were 22% and 14%, respectively.
M. Kamran
Abstract
The blasting operation is an important rock fragmentation technique employed in several foundation engineering disciplines such as mining, civil, tunneling, and road planning. Back-break (BB) is one of the adverse effects caused by the blasting operations that produces several effects including vulnerability ...
Read More
The blasting operation is an important rock fragmentation technique employed in several foundation engineering disciplines such as mining, civil, tunneling, and road planning. Back-break (BB) is one of the adverse effects caused by the blasting operations that produces several effects including vulnerability of mining machinery, bench slope design, and risks to the next blast-patterns due to the eruption of gases from several discontinuities in jointed rock masses. Several techniques have been executed by the researchers in order to predict BB in the blasting operations. However, this is the first work to implement a-state-of-the-art Catboost-based t-distributed stochastic neighbor embedding (t-SNE) approach to predict BB. A total of 62 datasets having 12 influential BB-generating features are collected from genuine blasting patterns. A novel dimensionality depletion technique t-SNE that operates the Kullback-Leibler divergence interpretation is employed to tailor the pioneer exaggeration of the blasting dataset. Then the t-SNE dataset obtained is split into a 70:30 ratio of the training and testing datasets. Finally, the Catboost method is implemented on a low-dimensionality blasting database. The performance evaluation criterion confirms that the BB predictive model is more stable with a goodness of fit = 99.04 in the training dataset, 97.26 in the testing datasets, and could anticipate a more accurate prediction. Moreover, the model presented in this work performs superior to the existing publicly available execution of BB. In summary, this model can be practiced in order to predict BB in several rock engineering practices and mining industry scenarios.
Akbar Esmaeilzadeh; Sina Shaffiee Haghshenas; Reza Mikaeil; Giuseppe Guido; Roohollah Shirani Faradonbeh; Roozbeh Abbasi Azghan; Amir Jafarpour; Shadi Taghizadeh
Abstract
Iran is one of the countries with the largest number of quarry mines in the world. Diamond cutting wire is usually used in quarries to cut dimension stone cubes, which is accompanied by hazardous events. Therefore, detecting and investigating the possible quarry risks is crucial to have a safe and sustainable ...
Read More
Iran is one of the countries with the largest number of quarry mines in the world. Diamond cutting wire is usually used in quarries to cut dimension stone cubes, which is accompanied by hazardous events. Therefore, detecting and investigating the possible quarry risks is crucial to have a safe and sustainable mining operation. In mine exploitation, maintaining the safety of vehicles and increasing the knowledge of personnel regarding safety issues can considerably mitigate the number or radius of effect of hazards. Hence, the incidents and risks in the West-Azerbaijan quarries in Iran are investigated in this work. To do so, a list of the hazards and their descriptions are first prepared. Then the hazard risk rating is conducted using the Failure Modes and Effects Analysis (FMEA) method. The number of priorities is calculated for each incident based on probability, intensity, and risk detection probability. Finally, the main causes of risks in the studies quarries are identified. The results obtained show that the most likely dangers in dimensional stone mines in West Azerbaijan are diamond cutting wire breaking, rock-fall, and car accidents, with the priority numbers of 216, 180, and 135, respectively. These hazards can be mitigated by applying some preservative activities such as timely cutting wire replacement, utilizing an intelligent system for cutting tool control, necessary personal training, and considering some preservative points.
K. Tolouei; E. Moosavi; A.H. Bangian Tabrizi; P. Afzal; A. Aghajani Bazzazi
Abstract
It is significant to discover a global optimization in the problems dealing with large dimensional scales to increase the quality of decision-making in the mining operation. It has been broadly confirmed that the long-term production scheduling (LTPS) problem performs a main role in mining projects to ...
Read More
It is significant to discover a global optimization in the problems dealing with large dimensional scales to increase the quality of decision-making in the mining operation. It has been broadly confirmed that the long-term production scheduling (LTPS) problem performs a main role in mining projects to develop the performance regarding the obtainability of constraints, while maximizing the whole profits of the project in a specific period. There is a requirement for improving the scheduling methodologies to get a good solution since the production scheduling problems are non-deterministic polynomial-time hard. The current paper introduces the hybrid models so as to solve the LTPS problem under the condition of grade uncertainty with the contribution of Lagrangian relaxation (LR), particle swarm optimization (PSO), firefly algorithm (FA), and bat algorithm (BA). In fact, the LTPS problem is solved under the condition of grade uncertainty. It is proposed to use the LR technique on the LTPS problem and develop its performance, speeding up the convergence. Furthermore, PSO, FA, and BA are projected to bring up-to-date the Lagrangian multipliers. The consequences of the case study specifies that the LR method is more influential than the traditional linearization method to clarify the large-scale problem and make an acceptable solution. The results obtained point out that a better presentation is gained by LR–FA in comparison with LR-PSO, LR-BA, LR-Genetic Algorithm (GA), and traditional methods in terms of the summation net present value. Moreover, the CPU time by the LR-FA method is approximately 16.2% upper than the other methods.
Imran Khan; Ravi Kumar Sharma
Abstract
An experimental study is carried out to improve the bearing capacity of soils by using geotextile. In the present study geotextile (tire reinforcement) is used as geotextile, whereas sand is used as a soil medium. This research work presents the results of laboratory load tests on model square footings ...
Read More
An experimental study is carried out to improve the bearing capacity of soils by using geotextile. In the present study geotextile (tire reinforcement) is used as geotextile, whereas sand is used as a soil medium. This research work presents the results of laboratory load tests on model square footings supported on reinforced sand beds. A total of twenty-seven load tests are conducted to evaluate the effects of single layer reinforcement placed below square model footings. The parameters of the testing program of the research work are the depth of reinforcement, the plan area of reinforcement, and the number of reinforcements. From the experimental data, it is indicated that there is an optimum reinforcement depth at which the bearing capacity is the highest. Also, the optimum size of reinforcement is found to be 1.5 B×1.5 B irrespective of the type of reinforcing materials used. The bearing capacity of reinforced sand is also found to increase with the number of reinforcement layer and reinforcement size when the reinforcement is placed within a certain effective zone with high relative density. The optimum placement position of geotextile is found to be 0.5B to 0.75B from the base of the footing .The tests are done at two different relative densities, i.e., 40% and 60%. The bulk unit weight of sandy soil is 14.81 KN/m³. Maximum gain in load carrying capacity is obtained when depth of reinforcement/width of footing (Dr/B) is 0.5 at relative density of 40% and 0.75 at a relative density of 60%.In addition, the data indicate that increasing reinforcement beyond a certain value would not bring about further increase in the bearing capacity of the soil.
J. Ghiasi-Freez; M. Ziaii; A. Moradzadeh
Abstract
An accurate reservoir characterization is a crucial task for the development of quantitative geological models and reservoir simulation. In the present research work, a novel view is presented on the reservoir characterization using the advantages of thin section image analysis and intelligent classification ...
Read More
An accurate reservoir characterization is a crucial task for the development of quantitative geological models and reservoir simulation. In the present research work, a novel view is presented on the reservoir characterization using the advantages of thin section image analysis and intelligent classification algorithms. The proposed methodology comprises three main steps. First, four classes of reservoir intervals are defined using a limited number of porosity and permeability values obtained from the core plugs of Kangan and Dalan formations. Then seven micro-scale features including distribution of pore types (interparticle, interaparticle, moldic, and vuggy), pore complexity, and cement distribution as well as textural characteristics are extracted from thin section images. Finally, the features extracted from each photomicrograph and its corresponding reservoir class are used as the training data for several intelligent classifiers including decision trees, discriminant analysis functions, support vector machines, K-nearest neighbor models and two ensemble algorithms, named bagging and boosting. The relationship between the micro-scale features and the reservoir classes was studied. Performance of all classifiers is evaluated using the concepts of accuracy, precision, recall, and harmonic average. The results obtained showed that the bagging decision tree delivered the best performance among the models and improved the accuracy of simple models up to 7.7% compared with the best single classifier.
Exploitation
H. Bakhshandeh Amnieh; M. Hakimiyan Bidgoli; H. Mokhtari; A. Aghajani Bazzazi
Abstract
Estimating the costs of blasting operations is an important parameter in open-pit mining. Blasting and rock fragmentation depend on two groups of variables. The first group consists of mass properties, which are uncontrollable, and the second one is the drill-and-blast design parameters, which can be ...
Read More
Estimating the costs of blasting operations is an important parameter in open-pit mining. Blasting and rock fragmentation depend on two groups of variables. The first group consists of mass properties, which are uncontrollable, and the second one is the drill-and-blast design parameters, which can be controlled and optimized. The design parameters include burden, spacing, hole length, hole diameter, sub-drilling, charge weight, charge length, stemming length, and charge density. Blasting costs vary depending on the size of these parameters. Moreover, blasting brings about some undesirable results such as air overpressure, fly rock, back-break, and ground vibration. This paper proposes a mathematical model for estimating the costs of blasting operations in the Baghak gypsum mine. The cost of blasting operations in the objective function is divided into three parts: drilling costs, costs of blasting system, and costs of blasting labours. The decision variables used to minimize the costs include burden, spacing, hole diameter, stemming length, charge density, and charge weight. Constraints of the model include the boundary and operational limitations. Air overpressure in the mine is also anticipated as one of the model constraints. The non-linear model obtained with consideration of constraints is optimized by simulated annealing (SA). After optimizing the model by SA, the best values for the decision variables are determined. The value obtained for the cost was obtained to be equal to 2259 $ per 7700 tons for the desired block, which is less than the blasting costs in the Baghak gypsum mine.
Muhammad Ahsan M.; T. Celik; B. Genc
Abstract
The distribution of stream sediments is usually considered as an important and very useful tool for the early-stage exploration of mineralization at the regional scale. The collection of stream samples is not only time-consuming but also very costly. However, the advancements in space remote sensing ...
Read More
The distribution of stream sediments is usually considered as an important and very useful tool for the early-stage exploration of mineralization at the regional scale. The collection of stream samples is not only time-consuming but also very costly. However, the advancements in space remote sensing has made it a suitable alternative for mapping of the geochemical elements using satellite spectral reflectance. In this research work, 407 surface stream sediment samples of the zinc (Zn) and lead (Pb) elements are collected from Central Wales. Five machine learning models, namely the Support Vector Regression (SVR), Generalized Linear Model (GLM), Deep Neural Network (DNN), Decision Tree (DT), and Random Forest (RF) regression, are applied for prediction of the Zn and Pb concentrations using the Sentinel-2 satellite multi-spectral images. The results obtained based on the 10 m spatial resolution show that Zn is best predicted with RF with significant R2 values of 0.74 (p < 0.01) and 0.7 (p < 0.01) during training and testing. However, for Pb, the best prediction is made by SVR with significant R2 values of 0.72 (p < 0.01) and 0.64 (p < 0.01) for training and testing, respectively. Overall, the performance of SVR and RF outperforms the other machine learning models with the highest testing R2 values.
Kamran Abbas; Adeel Nawazish; Navid Feroze; Nasar Male Ahmed
Abstract
In this work, an attempt is made to fit and identify the most appropriate probability distribution(s) for the analysis of seventeen rock samples including diorite, gypsum, marble, basalt, sandstone, limestone, apatite, slate, dolomite, granite-II, schist, gneiss, amphibolite, hematitle, magnetite, Shale, ...
Read More
In this work, an attempt is made to fit and identify the most appropriate probability distribution(s) for the analysis of seventeen rock samples including diorite, gypsum, marble, basalt, sandstone, limestone, apatite, slate, dolomite, granite-II, schist, gneiss, amphibolite, hematitle, magnetite, Shale, and granite-I using laser-induced breakdown spectroscopy. The graphical assessment and visualization endorse that the rock dataset series are positively skewed. Therefore, Frechet, Weibull, log-logistic, log-normal, and generalized extreme value distributions are considered as candidate distributions, and the parameters of these distributions are estimated by maximum likelihood and Bayesian estimation methods. The goodness of fit test and model selection criteria such as the Kolmogorov-Smirnov test, Akaike Information Criterion, and Bayesian Information Criterion are used to quantify the accuracy of the predicted data using theoretical probability distributions. The results show that the Frechet, Weibull, and log-logistic distributions are the best-fitted probability distribution for rock dataset. Cluster analysis is also used to classify the selected rocks that share common characteristics, and it is observed that diorite and gypsum are placed in one cluster. However, slate, dolomite, marble, basalt, sandstone, schist, granite-II, and gneiss rocks belong to different clusters. Similarly, limestone and apatite appeare in one cluster. Likewise, shale, granite-I, magnetite, amphibolite, and hematitle appeare in a different cluster. The current work demonstrate that coupling of laser-induced breakdown spectroscopy with suitable statistical tools can identify and classify the rocks very efficiently.