Rock Mechanics
Hamed Farajollahi; Mohammad Mohammadi; Mohammad Hossein Khosravi
Abstract
A better understanding of rock mass behavior is an essential part of the design and construction of underground structures. Any improvement in the understanding of the behavior of rock mass will facilitate the improvement of the design in terms of the safety of the working environment, long-term safety ...
Read More
A better understanding of rock mass behavior is an essential part of the design and construction of underground structures. Any improvement in the understanding of the behavior of rock mass will facilitate the improvement of the design in terms of the safety of the working environment, long-term safety of the structure, environmental effects, and sound management of public or private resources. Thus, in step one in this paper the experience gained from the application of the GDE (Geo Data Engineering) multiple graph approach for rock mass classification and assessment of its behavior through the course of excavation of the Alborz tunnel is presented. The predicted hazards are compared with the experienced problems and suggestions are given to be considered in future works of tunnel construction. In step two, the GDE multiple graph approach is compared to the rock mass behavior types proposed by Palmstrom & Stille (2007) in terms of the continuity of rock mass. The result of this comparison together with the data obtained from rock mass classification in the Alborz tunnel are used to develop a system that determines the applicability of the rock bolt supporting factor (RSF) in different rock mass behavior classes.
Rock Mechanics
Ghorban Khandouzi; Mohammad Hossein Khosravi
Abstract
Granular materials used in engineering structures tend to experience arching under different geotechnical factors. Arching is a factor of load transfer from the destroyed zone to stable areas in these structures. Soil arching plays an important role in stress redistribution, settlement, and load on supports ...
Read More
Granular materials used in engineering structures tend to experience arching under different geotechnical factors. Arching is a factor of load transfer from the destroyed zone to stable areas in these structures. Soil arching plays an important role in stress redistribution, settlement, and load on supports in tunneling. This paper reviews the effect of various parameters on the development of soil arching and formation of expansion and contraction zones around the tunnel. A comprehensive literature review, analysis of new published papers, and investigations were conducted to study the effects of various parameters on soil arching. The results were obtained by studying the formation of shear bands, deformed zones, and their development. The achieved results of investigations show that soil arching and ground deformation around tunnels in sandy grounds are complex phenomena that require careful consideration during tunnel construction. Also the results reveal that despite the arching zone, a loosened zone with non-linear slip surfaces forms above the tunnel. With the onset of tunnel convergence, initial non-linear sliding surfaces appear, and the arching area forms above the tunnel. When tunnel convergence increases, a stable arch forms inside the arching zone, and a de-stressed area as a loosened zone is created under the stable arch. Understanding of soil arching, ground deformation, and the stable arch formed inside the arching zone around tunnels in sandy grounds is very important for the engineers evaluating stress redistribution and load on tunnel supports. Also understanding these issues can help the designers and practitioners make informed decisions during tunnel construction.
M. Bahaaddini; M. Serati; M. H. Khosravi; B. Hebblewhite
Abstract
A proper understanding of the shear behaviour of rock joints and discontinuities is yet a remaining challenge in the rock engineering research works owing to the difficulties in quantitatively describing the joint surface roughness both at the field and the laboratory scales. Several instruments and ...
Read More
A proper understanding of the shear behaviour of rock joints and discontinuities is yet a remaining challenge in the rock engineering research works owing to the difficulties in quantitatively describing the joint surface roughness both at the field and the laboratory scales. Several instruments and techniques have been developed over the years for the surface characterisation of joints at the field- and laboratory-scale investigations, amongst which the application of the photogrammetry methods has obtained a growing popularity. This work evaluates the applicability of the photogrammetry techniques for the characterisation of joint surface topography and texture at micro-scales, which has been largely understudied in the literature. Three tensile joint surfaces are digitized using photogrammetry, and the results are compared with those obtained from laser scans with a high 3D accuracy. A comprehensive statistical analysis is then undertaken on the digitized point clouds in order to assess the performance of photogrammetry in surface characterisation. The results of this work show that the height differences between the resulting point clouds from the two adopted techniques (photogrammetry and 3D laser scanning) follow the normal distribution with the mean values close to zero. The statistical analyses illustrate that the measured joint surfaces using the photogrammetry techniques are in good agreement with the laser scanning data, confirming that photogrammetry is a capable method for characterising the joint surface roughness even at micro-scales. Interestingly, the results obtained further indicate that the accuracy and preciseness of the photogrammetry techniques are independent from the joint roughness coefficient but the camera and configuration parameters remarkably control the performance of the measurement.
F. Abbasi; M.H. Khosravi; A. Jafari; Ali Bashari; B. Alipenhani
Abstract
The instability of the roof and walls of the tunnels excavated in coal mines has always attracted the attention of the miners and experts in this field. In this work, the instability of the main tunnels of the mechanized Parvadeh coal mine in Tabas, Iran, at the intersection with coal seam is studied. ...
Read More
The instability of the roof and walls of the tunnels excavated in coal mines has always attracted the attention of the miners and experts in this field. In this work, the instability of the main tunnels of the mechanized Parvadeh coal mine in Tabas, Iran, at the intersection with coal seam is studied. The main tunnels of this mine show significant horizontal displacements due to the complex ground conditions and great depth. The behavior of the rock mass surrounding the tunnel is investigated using various experimental methods, and according to the results obtained, the surrounding rock mass has squeezing conditions. In order to analyze the stability of the main tunnels, a series of 2D and 3D numerical modelings are performed using the FLAC2&3D finite difference software, and the results obtained are compared with the actual displacement values recorded in the walls of the main tunnels of the mine. The analysis results show that the tunnels under study are unstable with a steel frame support, and therefore, the use of different support systems for the stabilization is investigated. The results of modeling different types of support systems show that the use of shotcrete instead of galvanized sheet (as strut) does not have a significant effect on the reduced displacements. Also although the installation of steel sets is very effective in preventing the displacement of the walls, due to the swelling problems in the tunnel bottom and the placement of the conveyor and haulage rail, it cannot be used in practice. Finally, the use of truss bolt has yielded good results, and it can be proposed as a new support system in these tunnels. In addition, the modeling results show that in case the coal seam is higher than the tunnel foot, less displacement will occur in the tunnel walls compared to the other cases. In other words, changing the tunnel level in the future excavations can help reduce the displacements.
H. Haghgouei; A. Reza Kargar; M. H. Khosravi; M. Amini
Abstract
In many engineering constructions, the foundations should be built adjacent to each other. Therefore, the effect of interfering of close foundations should be considered in the design stage. In this research work, the effect of interference of closely separated foundations resting on a slope on the elastic ...
Read More
In many engineering constructions, the foundations should be built adjacent to each other. Therefore, the effect of interfering of close foundations should be considered in the design stage. In this research work, the effect of interference of closely separated foundations resting on a slope on the elastic settlement is investigated by considering a semi-analytical solution. The distribution of stress due to the footing pressure in the slope is computed by a proposed Airy stress function, and then by employing the finite difference scheme, the displacement of the footings is calculated. The results obtained show that by increasing the distance between the foundations, the interference influence on the ratio of settlement will be diminished. However, this behavior is highly linked to the slope characteristics. For a slope with a height of 10 times of footing width, beyond an S/B ratio larger than 10, the effect of interference is not tangible, and the footings behave like an isolated foundation. By decreasing the slope height, this behavior will occur at a lower S/B.
H. Sarfaraz; M. H. Khosravi; T. Pipatpongsa
Abstract
One of the most important tasks in designing the undercut slopes is to determine the maximum stable undercut span to which various parameters such as the shear strength of the soil and the geometrical properties of the slope are related. Based on the arching phenomenon, by undercutting a slope, the weight ...
Read More
One of the most important tasks in designing the undercut slopes is to determine the maximum stable undercut span to which various parameters such as the shear strength of the soil and the geometrical properties of the slope are related. Based on the arching phenomenon, by undercutting a slope, the weight load of the slope is transferred to the adjacent parts, leading to an increase in the stability of the slope. However, it may also lead to a ploughing failure on the adjacent parts. The application of counterweight on the adjacent parts of an undercut slope is a useful technique to prevent the ploughing failure. In other words, the slopes become stronger as an additional weight is put to the legs; hence, the excavated area can be increased to a wider span before the failure of the slope. This technique could be applied in order to stabilize the temporary slopes. In this work, determination of the maximum width of an undercut span is evaluated under both the static and pseudo-static conditions using numerical analyses. A series of tests are conducted with 120 numerical models using various values for the slope angles, the pseudo-static seismic loads, and the counterweight widths. The numerical results obtained are examined with a statistical method using the response surface methodology. An analysis of variance is carried out in order to investigate the influence of each input variable on the response parameter, and a new equation is derived for computation of the maximum stable undercut span in terms of the input parameters.
V. Heydarnoori; M. H. Khosravi; M. Bahaaddini
Abstract
The cavability assessment of rock mass cavability and indicating the damage profile ahead of a cave-back is of great importance in the evaluation of a caving mine operation, which can influence all aspects of the mine operation. Due to the lack of access to the caved zones, our current knowledge about ...
Read More
The cavability assessment of rock mass cavability and indicating the damage profile ahead of a cave-back is of great importance in the evaluation of a caving mine operation, which can influence all aspects of the mine operation. Due to the lack of access to the caved zones, our current knowledge about the damage profile in caved zones is very limited. Among the different approaches available, physical modelling can provide a useful tool for assessment of the cave propagation and understanding the cave-back mechanism. Despite the general belief of the continuous damage profile ahead of a cave, the recent studies have shown a different mechanism of banding fracture. In order to investigate the caving mechanism ahead of a cave, a base friction apparatus is designed in this work. The base friction powder is used as the modelling material for physical testing, where its strength properties is significantly dependent on its unit weight. The effects of the material’s unit weight and the undercutting process on the cavability and cave-back height are studied. The experimental results undertaken in this research work clearly confirm the banding fracture mechanism in the caved zone, rather than continuous yielding. The effect of the undercutting sequence on the cave-back height is investigated through three different scenarios of symmetric undercutting with a gradual increase in span, symmetric undercutting with a sudden increase in span, and asymmetric undercutting. The results obtained show that the ground deformation is significantly dependent on the undercutting sequence, where choosing a greater undercutting span results in a faster cave propagation and smaller accessible undercut spans.
Gh. Khandouzi; H. Memarian; M. H. Khosravi
Abstract
The dynamic fracture characteristics of rock specimens play an important role in analyzing the fracture issues such as blasting, hydraulic fracturing, and design of supports. Several experimental methods have been developed for determining the dynamic fracture properties of the rock samples. However, ...
Read More
The dynamic fracture characteristics of rock specimens play an important role in analyzing the fracture issues such as blasting, hydraulic fracturing, and design of supports. Several experimental methods have been developed for determining the dynamic fracture properties of the rock samples. However, many used setups have been manufactured for metal specimens, and are not suitable and efficient for rocks. In this work, a new technique is developed to measure the dynamic fracture toughness of rock samples and fracture energy by modifying the drop weight test machine. The idea of wave transmission bar from the Hopkinson pressure bar test is applied to drop weight test. The intact samples of limestone are tested using the modified machine, and the results obtained are analyzed. The results indicate that the dynamic fracture toughness and dynamic fracture energy have a direct linear relationship with the loading rate. The dynamic fracture toughness and dynamic fracture energy of limestone core specimens under the loading rates of 0.12-0.56kN/µS are measured between 9.6-18.51MPa√m and 1249.73-4646.08J/m2, respectively. In order to verify the experimental results, a series of numerical simulation are conducted in the ABAQUS software. Comparison of the results show a good agreement where the difference between the numerical and experimental outputs is less than 4%. It can be concluded that the new technique on modifying the drop weight test can be applicable for measurement of the dynamic behavior of rock samples. However, more tests on different rock types are recommended for confirmation of the application of the developed technique for a wider range of rocks.
Rock Mechanics
H. Sarfaraz; M. H. Khosravi; M. Amini
Abstract
In layered and blocky rock slopes, toppling failure is a common mode of instability that may occur in mining engineering. If this type of slope failure occurs as a consequence of another type of failure, it is referred to as the secondary toppling failure. “Slide-head-toppling” is a type ...
Read More
In layered and blocky rock slopes, toppling failure is a common mode of instability that may occur in mining engineering. If this type of slope failure occurs as a consequence of another type of failure, it is referred to as the secondary toppling failure. “Slide-head-toppling” is a type of secondary toppling failures, where the upper part of the slope is toppled as a consequence of a semi-circular sliding failure at the toe of the slope. In this research work, the slide-head-toppling failure is examined through a series of numerical modeling. Phase 2, as a software written based on the finite element method, is used in this work. Different types of slide-head-toppling failures including blocky, block-flexural, and flexural are simulated. A good agreement can be observed when the results of the numerical modeling are compared with those for the pre-existing physical modeling and analytical method.
Rock Mechanics
R. Shafiei Ganjeh; H. Memarian; M. H. Khosravi; M. Mojarab
Abstract
Dynamic slope stability in open-pit mines still remains a challenging task in the computational mining design. Earthquake and blasting are two significant sources of dynamic loads that can cause many damages to open-pit mines in active seismic areas and during exploitation cycles. In this work, the effects ...
Read More
Dynamic slope stability in open-pit mines still remains a challenging task in the computational mining design. Earthquake and blasting are two significant sources of dynamic loads that can cause many damages to open-pit mines in active seismic areas and during exploitation cycles. In this work, the effects of earthquake and blasting on the stability of the NW slope of Chadormalu mine are compared by a numerical modeling method. The dynamic results show that the maximum displacement under earthquake and blasting loads within the slope are 844 mm and 146 mm, respectively. According to the shear strain results, both the earthquake and blasting waveforms are destructive, while the earthquake waveforms cause more damages to the slope. Moreover, the deterministic and probabilistic seismic hazard analyses are carried out to assess the seismicity of the mine area. The experimental results indicate that the maximum values for the vertical and horizontal accelerations are 0.55 g and 0.75 g, respectively. The maximum calculated acceleration is then scaled to the selected earthquake accelerograms. In order to show the effective impact of the established scale, the model is executed using the original accelerograms. The results obtained show that the established scale prevents overestimation and underestimation of the displacement and strain. Therefore, applying scaled accelerograms in a dynamic slope stability analysis in mine slopes leads to more reliable and robust results. The overall results show that a strong earthquake causes plenty of damages to the slope, and consequently, interrupts the mining cycle. Hence, the seismic study and dynamic slope stability should be considered as a part of the computational mining design.
Rock Mechanics
S. Ali Madadi; A. Majdi; M. H. Khosravi; A.R. Kargar
Abstract
Fracture mechanics is a vital component involved in studying the exact behavior of rock materials. Detection and assessment of the behavior of rock joints injected by grout plays an important role in numerical modelling in rock mechanic projects. The importance of mechanisms associated with initiation ...
Read More
Fracture mechanics is a vital component involved in studying the exact behavior of rock materials. Detection and assessment of the behavior of rock joints injected by grout plays an important role in numerical modelling in rock mechanic projects. The importance of mechanisms associated with initiation and propagation of cracks due to hydraulic fracturing has led to a considerable interest in investigation and analysis of this phenomenon. In this work, the process of propagation of cracks on the wall of boreholes, drilled in single and bi-material structures, was simulated in ABAQUS software employing the extended finite element method. The energy method was implemented to obtain the stress intensity factor and energy release rate through applying J integral around the crack tip. The method was applied to two rock types, diorite and granite at the Chadormalu iron mine located in the central part of Iran. It was concluded that assuming the same geometry, the possibility of crack propagation at the boundary between two materials was more than the single material medium. Therefore, in dealing with a bi-material medium, if the purpose is to measure the in situ stresses, the measurement should not be performed on the boundary between the two materials.
Rock Mechanics
M. H. Khosravi; T. Pipatpongsa; J. Takemura; M. Amini
Abstract
A series of physical modeling tests were conducted by means of a beam type geotechnical centrifuge machine in order to investigate the drainage impact on the slope failure mechanism under centrifugal acceleration. Meanwhile, the phenomenon of stress redistribution in undercut slopes and the formation ...
Read More
A series of physical modeling tests were conducted by means of a beam type geotechnical centrifuge machine in order to investigate the drainage impact on the slope failure mechanism under centrifugal acceleration. Meanwhile, the phenomenon of stress redistribution in undercut slopes and the formation of arching effect were studied. For this purpose, a poorly graded sandy soil (Silica sand No. 6) as well as a relatively well-graded sandy soil (Edosaki sand) were used as the modeling materials. The humid modeling material was compacted on a low friction oblique rigid plate simulating the potential slippage plane. The process of undercutting was conducted, while the earth pressure redistribution inside the model was recorded by means of a miniature set of pressure cells. The results obtained showed completely different failure mechanisms for the two different modeling soils. By undercutting the slope, the earth pressure redistributed and the arch action was formed in a slope model made from a well-graded soil leading to a clear arch-shaped failure. However, in using the poorly graded soil, the water was drained out during centrifuge g-up, the modeling material properties changed, and an avalanche failure was observed. Therefore, in selecting a humid compacted soil as the centrifugal modeling material, a well-graded soil is recommended.
